American Dryer Corp. ML-175 Скачать руководство пользователя | Manualshive

Страница: 48 / 54

background image

44

American Dryer Corp.

113406-1

BEFORE YOU START!

CHECK LOCAL CODES AND PERMITS

Call your local water company or the proper municipal authority for information regarding local codes.

IMPORTANT:

It is your responsibility to have

ALL

plumbing connections made by a qualified

professional to ensure that the plumbing installation is adequate and conforms to local,
state, and federal regulations or codes.

IMPORTANT:

It is the installation or owners responsibility to see that the necessary or required
water, water pressure, pipe size, or connections are provided. Manufacturer assumes
no responsibility if the fire suppression system

is not

connected, installed, or

maintained properly.

INSTALLATION

1. Requirements

The fire suppression system

must be

supplied with a minimum water pipe size of 1/2” and be provided

with 40 psi +/- 20 psi (2.75 bar +/- 1.37 bar) of pressure. For use of optional manual bypass, a second
source with the same piping and pressure requirements is required.

Flexible 1/2 feeds

must be

provided to avoid damage to electric water solenoid valve by vibration.

IMPORTANT:

Flexible supply line/coupling

must be

used. Solenoid valve failure due to hard

plumbing connections WILL VOID WARRANTY.

If the rear area of the dryer, or the water supply is located in an area where it will be exposed to
cold/freezing temperatures, provisions

must be

made to protect these water lines from freezing.

WARNING:

If the water in the supply line or water solenoid valve freezes, the fire suppression system

will be

INOPERATIVE!!

IMPORTANT:

Appliance is to be connected to the water mains using a new hose set and the old
hose set

should not be

reused.

«
...
46
47
48
49
50
...
»

Содержание ML-175























































Отзывы:

Нет отзывов

Похожие инструкции для ML-175

Бренд: Wahl Страницы: 116

Бренд: BaByliss PRO Страницы: 72

NANO TITANIUM Portofino 6600

Бренд: BaBylissPro Страницы: 13

Бренд: V-ZUG Страницы: 44

TOP Style SC-HD70T09

Бренд: Scarlett Страницы: 12

Бренд: DCG Страницы: 28

Smart Oven Air Fryer SOV860

Бренд: Sage Страницы: 84

Бренд: Gaggenau Страницы: 52

Бренд: TurboTronic Страницы: 10

Бренд: Asko Страницы: 32

Бренд: XPower Страницы: 15

PULVIS MINI SPRAY GB210A

Бренд: Yamato Страницы: 58

Бренд: GE Страницы: 32

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 40

Бренд: GE Страницы: 32

Бренд: baridi Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды