American Dryer Corp. ML-175 Скачать руководство пользователя | Manualshive

Страница: 17 / 54

background image

113406-1

www.amdry.com

13

IMPORTANT:

Exhaust back pressure measured by a manometer at each basket (tumbler) exhaust
duct area

must be

no less than 0 and

must not exceed

0.3 inches (0.74 mb) of water

column (W.C.).

It is suggested that the ductwork from each dryer not exceed 15 feet (4.57 meters) with no more than three
(3) elbows (excluding dryer connections). If the ductwork exceeds 15 feet (4.57 meters) or has numerous
elbows, the cross-sectional area of the ductwork

must be

increased in proportion to the length and number

of elbows in it. In calculating duct size, the cross-sectional area of a square or rectangular duct

must be

increased twenty percent (20%) for each additional 15 feet (4.57 meters). The diameter of a round
exhaust duct

should be

increased ten percent (10%) for each additional 10 feet (3.04 meters). Each 90º

elbow is equivalent to an additional 40 feet (12.19 meters), and each 45º elbow is equivalent to an additional
20 feet (6.09 meters).

IMPORTANT:

For extended ductwork runs, the cross section area of the ductwork can only be
increased to an extent. Maximum proportional ductwork runs

cannot

exceed 15 feet

(4.57 meters) more than the original limitations of 15 feet (4.57 meters) with three (3)
elbows. When the ductwork approaches the maximum limits as noted in this manual,
a professional heating, ventilating, and air-conditioning (HVAC) firm

should be

consulted for proper venting information.

ALL

ductwork

should be

smooth inside with no projections from sheet metal screws or other obstructions,

which will collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be
connected.

ALL

ductwork joints

must be

taped to prevent moisture and lint from escaping into the

building. Inspection doors

should be

installed at strategic points in the exhaust ductwork for periodic

inspection and cleaning of lint from the ductwork.

«
...
15
16
17
18
19
...
»

Содержание ML-175























































Отзывы:

Нет отзывов

Похожие инструкции для ML-175

Бренд: Oster Страницы: 12

Бренд: CPG Страницы: 13

Easy Fry Compact Digital

Бренд: TEFAL Страницы: 16

Бренд: DeLonghi Страницы: 22

Global Design 815U

Бренд: Toastmaster Страницы: 16

Бренд: Buffalo Страницы: 48

Бренд: Maytag Страницы: 20

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 32

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 60

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды