AMD AMD-761 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 264

background image

Chapter 2

AMD-761™ System Controller Programmer’s Interface

71

24081D—February 2002

AMD-761™ System Controller Software/BIOS Design Guide

Preliminary Information

Bit Definitions

PCI Arbitration Control (Dev0:F0:0x84)

Bit

Name

Function

31–24

AGP_VGA_BIOS

AGP VGA BIOS

These bits when set indicate that the corresponding (16-KByte) segment should be
mapped to the AGP PCI bus. Bit 24 corresponds to the addresses 0xC0000–0xC3FFF and
bit 31 maps addresses 0xDC000–0xDFFFF to the AGP PCI interface. Set one or more of
these bits if the AGP graphics card has a ROM BIOS.

23

Tgt_Latency

Target Latency

This bit is designed to ensure that the AMD-761™ system controller is compliant to the PCI
maximum target latency rule. Note that this compliance applies only to the PCI bus and
not the AGP bus.
0 = AMD-751™ system controller-compatible, the AMD-761 system controller does not

disconnect a master when it cannot service a read request within 32 PCI clock
periods (initial latency) or 8 clocks (subsequent data cycles).

1 = If the AMD-761 system controller cannot respond to a memory read within 32 clocks

for the initial access, or 8 clocks for each subsequent access, it forces a retry.

Note:

To prevent potential deadlocks, set this bit and clear bit 3 (Tgt_Lat_Tim_Dis) if
the system has PCI to AGP traffic.

22–18

Reserved

Reserved

17

AGP_Chain_En

Enable AGP Chaining

When set, CPU writes to the AGP bus are chained together.

16

PCI_Chain_En

Enable PCI Chaining

When set, CPU writes to PCI are chained together.

15

MDA_Debug

MDA Debug

This bit allows monochrome display adapters (MDA) to be used simultaneously with AGP
cards for debug of AGP device drivers. The behavior of the AMD-761 system controller
display adapters is a function of this bit and the VGA Enable in (D1:0x3C[19]) as follows:
MDA address ranges:

Memory: 0B0000h–0B7FFFh
I/O: 3B4h, 3B5h, 3B8h, 3B9h, 3BAh, 3BFh

VGA = 0, MDA = 0: all MDA and VGA references go to PCI

VGA = 0, MDA = 1: operation undefined

VGA = 1, MDA = 0: all VGA references go to AGP, MDA only (I/O 3BFh) goes to PCI

VGA = 1, MDA = 1: all VGA references go to AGP, all MDA (including memory) go to PCI

14

PCI_WR_Post
_Rtry

PCI Write Post Retry

When set, this bit enables retries on PCI if there are pending posted writes.

13

AGP_WR_Post
_Rtry

AGP Write Post Retry

When set, this bit enables retries on the AGP bus if there are pending posted writes.

«
...
81
82
83
84
85
...
»

Содержание AMD-761









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AMD-761

Бренд: Acclaim Lighting Страницы: 32

Бренд: Jeep Страницы: 19

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: PACH & COMPANY Страницы: 4

Бренд: Watlow Страницы: 4

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 140

Бренд: YOKOGAWA Страницы: 150

Бренд: YOODA Страницы: 3

Бренд: YMGI Страницы: 8

Бренд: Kampmann Страницы: 5

Бренд: Technische Alternative Страницы: 68

Бренд: TechGrow Страницы: 34

SAE 07.2 Series

Бренд: AUMA Страницы: 116

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Бренд: MELICONI Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды