AMD AMD-761 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 264

background image

Chapter 2

AMD-761™ System Controller Programmer’s Interface

45

24081D—February 2002

AMD-761™ System Controller Software/BIOS Design Guide

Preliminary Information

Bit Definitions

ECC Mode/Status (Dev0:F0:0x48)

Bit

Name

Function

31–16

Reserved

Reserved

15-14

SERR_Enable

System Error Enable

These bits control the AMD-761™ system controller’s reporting of ECC errors to the
system via the SERR# pin on the PCI bus. Note that SERR# assertion is still subject to the
normal PCI SERR# enable (bit 8 in Dev 0:F0:0x04). Refer to Table 7 on page 34 for
details about SERR# assertion and status.
00 = SERR# assertion is disabled.

X1 = Multiple bit errors force SERR# assertion.

1X = Single bit errors force SERR# assertion.

13

Reserved

Reserved

12

ECC_Diag

Error Correcting Code Diagnostic Mode Enable

0 = ECC diagnostic mode disabled

1 = ECC diagnostic mode enabled

When the ECC diagnostic mode is enabled, the AMD-761 system controller always
writes 0x00 to the ECC byte to aid testing of the ECC logic. During partial writes, the
RMW sequence still occurs, but the ECC bits are always written to 0x00.
For reads, the ECC circuitry is unaffected by the ECC_Diag bit. The ECC code returned
from memory is checked, and errors are reported in the ECC_Status bits as usual.
Correction is not performed in this mode.

11–10

ECC_Mode

Error Correcting Code Mode

00 = ECC disabled, no error detection or correction is performed.

01 = EC_HiPerf mode enabled. Error checking and status reporting is enabled. Data

destined for the PCI/AGP and memory (RMR) is

not

corrected.

10 = ECC_HiPerf mode enabled. Error checking and status reporting is enabled. Data

destined for the PCI/AGP and memory (RMR) is corrected.

11 = ECC_Scrub mode enabled. Error checking and status reporting is enabled. Data

destined for the PCI/AGP and memory (RMR) is corrected. The memory
contents are corrected (scrubbed) after all reads with errors.

9–8

ECC_Status

Error Correcting Code Status

This bit field indicates the status of the ECC detect logic as follows:
00 = No error

X1 = MED: multi-bit error detect

1X = SED: single-bit error detect

The ECC status bits and corresponding failing chip-select indicators are set by the first
error detected of each type (SED or MED). The AMD-761 system controller does not log
any new errors of each type or assert SERR# until software clears the associated
ECC_Status bit by writing a 1.

«
...
55
56
57
58
59
...
»

Содержание AMD-761









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AMD-761

Бренд: Tapeswitch Страницы: 13

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Origami 4M-006-01

Бренд: 4 Moms Страницы: 28

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: D+H Страницы: 14

Бренд: Dahua Страницы: 137

Бренд: Parker Страницы: 42

Бренд: IN-COMMAND Страницы: 47

Бренд: SYCLOPE Страницы: 60

PDS CONTROL Series

Бренд: S&P Страницы: 32

CentralControl CC41

Бренд: Becker Страницы: 48

Бренд: GSK Страницы: 32

Бренд: Grundfos Страницы: 16

Бренд: Loewe Страницы: 62

Бренд: Shimaden Страницы: 32

Бренд: Hard Head Страницы: 10

Бренд: J+J Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды