AMCI SMD17K Скачать руководство пользователя страница 72

Страница: 72 / 98

OMMAND

ATA

ORMAT

SMD17K User Manual

ADVANCED MICRO CONTROLS INC.

Input Data Format

The correct format for the Network Input Data when the SMD17K is in Command Mode is shown below.

† Note that this is the value of the most recently programmed motor current. It is not the actual



current being sent to the motor when the input data was read.

Table R6.18 Network Input Data Format: Command Mode

STATUS_word0 Format

Figure R6.4 Command Mode: Status Word 0 Format

Bit 15: Mode_Flag –

Set to “0” when in Command Mode.

Bit 14: Module_OK –

“1” when the SMD17K is operating without a fault, “0” when an internal fault condi-

tion exists.

Bit 13: Configuration_Error –

“0” when the unit has a valid configuration in memory. “1” if there is one or

more errors in the CoE SDO configuration data written to the unit. See

Configuration Data Format

which starts on page 55, for information on the format of the Configuration Data.

Bit 12: Command_Error –

“1” when an invalid command has been written to the SMD17K. This bit can

only be reset by the

Reset_Errors

bit, Command Word 0, Bit 10.

Bit 11: Input_Error –

“1” when:



Emergency Stop input has been activated



Either of the End Limit Switches activates during any move operation except for homing



Starting a Jog Move in the same direction as an active End Limit Switch



If the opposite End Limit Switch is reached during a homing operation



A SyncManager 2 timeout event has occurred. This is indicative of a networking error that
occured during the EtherCAT Pre-OP and OP states.

This bit is reset by a

Reset Errors

command. The format of the command is given on page 69.

ESI File

Name

Data

Size

Function

STATUS_word0

UINT

Status Word 0

STATUS_word1

UINT

Status Word 1

Motor_Position

DINT

Current commanded motor position

Encoder_Position

DINT

Current encoder position.



(Zero if encoder is not available or disabled.)

Trapped_Encoder_Position

DINT

Last captured encoder position

Motor_Current

UINT

Motor current of last move.

†

Jerk

UINT

Jerk value of last move.

STATUS_word0

15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00

Mod

le_OK

Con

g_Err

Comm

and

_Err

Inp

t_Er

Assy

Seg

_As

y_Mode

Mov

_Cmp

ele

rat

At_

ome

ped

_Ho

ld_St

g_CCW

ing_

Содержание SMD17K



































































































Результаты поиска

Содержание SMD17K

Отзывы:

Бренды по названию

Популярные бренды

AMCI SMD17K, Руководство пользователя

Результаты поиска

Содержание SMD17K

Отзывы:

Бренды по названию

Популярные бренды