Amada 1000ADP Скачать руководство пользователя страница 52

Страница: 52 / 112

CHAPTER 4: OPERATING INSTRUCTIONS

125ADP/300ADP/1000ADP DUAL PULSE RESISTANCE WELDING POWER SUPPLY

4-4

990-922

To modify

pulse duration

, press the

PULSE SELECT

button until the pulse length you want is

indicated beneath the 3-digit energy display.

NOTE:

The

Very Short

setting provides the shortest duration. The

Short

setting

provides the

highest peak current for a given energy setting The

Long

setting provides the longest duration

and lowest peak current for a given energy setting. The

Medium

setting provide and

intermediate option between the

Short

and

Long

settings. Upslope applies to the

Short

Medium

and

Long

settings only, and is turned ON or OFF with the

PULSE SELECT

button.

Note:

Pulse duration is not user settable on the 1000ADP

To modify

POLARITY

, in edit mode, press the

POLARITY SELECT

button repeatedly until the

polarity you want is indicated in the display.

Note: Polarity is not user settable on the 1000ADP

To modify the

squeeze time

, press the

SQZ/HOLD

button. The

SQUEEZE

field will be

highlighted. Press the arrow to increase squeeze time or press the arrow to decrease the
squeeze time.

To modify the

hold time

, press the

SQZ/HOLD

button again. The

HOLD

field will be

highlighted. Press the arrow to increase hold time or press the arrow to decrease hold
time.

To modify the settings for Pulse 2, press and hold the

Pulse 2

button to enter edit mode.

10.

Repeat steps 4 through 6 to program the settings for Pulse 2.

11.

Press the

SAVE

button to save any changes made. To exit “editing” mode

without

accepting

changes, press the RUN button on the front panel which will activate the

SAVE

prompt, then

press

CLEAR

to discard changes.

Set Peak Current Monitor Limits

Each of the 63 schedules has an associated set of

Monitor Limits

. To edit these limits, select the desired

schedule, then:

Press the

LIMITS/COUNTERS

button to select this screen.

To edit the limits for Pulse 1, press and hold the

PULSE 1

button for about one second. The

screen will turn black to indicate that the Power Supply is in edit mode. The upper limit for
Pulse 1 will be highlighted. Press the arrow to increase limit or press the arrow to
decrease the limit.

To edit the lower limit for Pulse 1, press the

PULSE 1

button again. The lower limit will be

highlighted. Press the arrow to increase limit or press the arrow to decrease the limit.

To edit the Action for Pulse 1, press the Pulse 1 button again. Press the or arrow to select
between

CONTINUE

INHIBIT PULSE 2

NOTE:

When

CONTINUE

is selected, Pulse 2 is enabled whether or not Pulse 1 is within

limits. When

INHIBIT PULSE 2

is selected

, Pulse 2 is inhibited when Pulse 1 is out of limits.

Use the

PULSE 2

button to set the upper and lower limits for Pulse 2.

Содержание 1000ADP

















































































































Результаты поиска

Содержание 1000ADP

Отзывы:

Бренды по названию

Популярные бренды

Amada 1000ADP, Руководство по эксплуатации

Результаты поиска

Содержание 1000ADP

Отзывы:

Бренды по названию

Популярные бренды