Amada 1000ADP Скачать руководство пользователя страница 47

Страница: 47 / 112

CHAPTER 3. USING DISPLAY SCREENS

125ADP/300ADP/1000ADP DUAL PULSE RESISTANCE WELDING POWER SUPPLY

990-922

3-11

REPEAT MODE

Press the

MENU

button again to highlight the

REPEAT MODE

selection. When this is set to

, the control provides an automatic repeat of

the weld sequence for simple automated air
actuated applications. This weld function is
ideal for volume production which requires a
single schedule.

REPEAT MODE

can

only

be used with an Air

Actuated Weld Head. On Force Fired Air
Actuated Weld Heads, weld current begins
when both levels of a two-level Foot Switch are
closed and held down and then the Force Firing
Switch in the Air-Actuated Weld Head closes
sending a fire signal.

When

REPEAT MODE

is used with a Non-Force Fired Air Actuated Weld Head, the Squeeze (SQZ)

Period must be used to allow sufficient time for the electrodes to close and apply the required weld force
to the parts

before

the Weld Period begins. Weld current begins when the Squeeze Period ends and a

fire signal is received. During this whole operation

both

levels of a two-level Foot Switch must remain

closed to continue in

REPEAT MODE

When

REPEAT MODE

is used with any type of Air Actuated Weld Head, the Hold Period can be used to

automatically keep the electrodes closed on the parts after weld current has terminated to provide
additional heat sinking or parts cooling.

REPEAT TIME

, which is applicable only to

REPEAT MODE

, sets

the cycling rate between welds by controlling how long the electrodes remain open.
When

REPEAT MODE

is set to

, and the user keeps the footswitch depressed and firing switch closed,

the control will repeatedly actuate the weldhead and perform the weld sequence. If set to

, a

REPEAT

TIME

other than

must also be set.

You should specify the

REPEAT TIME

so that it is sufficient to allow the weld head to open the

electrodes and to allow you to reposition the work piece before the entire welding sequence repeats.
When

REPEAT MODE

is set to

OFF

, this function is deactivated.

Содержание 1000ADP

















































































































Результаты поиска

Содержание 1000ADP

Отзывы:

Бренды по названию

Популярные бренды

Amada 1000ADP, Руководство по эксплуатации

Результаты поиска

Содержание 1000ADP

Отзывы:

Бренды по названию

Популярные бренды