Amada 1000ADP Скачать руководство пользователя страница 46

Страница: 46 / 112

CHAPTER 3. USING DISPLAY SCREENS

125ADP/300ADP/1000ADP DUAL PULSE RESISTANCE WELDING POWER SUPPLY

3-10

990-922

RESET DEFAULTS

Press the

MENU

button again to select the

RESET

DEFAULTS

. The default selection is

OFF.

To set all schedules, limits, weld counter, weld
counter limits and all menu items back to their
factory default values, select

, then press

SAVE

to save changes.

To discard changes, press

RUN

to activate the

SAVE PROMPT

and at the prompt, press

CLEAR

to discard changes.
After saving or discarding new settings, the
display will revert to the original screen selected.

FAST WELDING

Press the

MENU

button again to highlight the

FAST WELDING

selection.

When this is set to

OFF

, weld data is saved to

non-volatile memory periodically.
When

FAST WELDING

is set to

, weld data is

saved to non-volatile memory only when the
user presses the

SAVE

button.

See Chapter 4 for more information about the

FAST WELDING

feature.

Содержание 1000ADP

















































































































Результаты поиска

Содержание 1000ADP

Отзывы:

Бренды по названию

Популярные бренды

Amada 1000ADP, Руководство по эксплуатации

Результаты поиска

Содержание 1000ADP

Отзывы:

Бренды по названию

Популярные бренды