Amada 1000ADP Скачать руководство пользователя страница 41

Страница: 41 / 112

CHAPTER 3. USING DISPLAY SCREENS

125ADP/300ADP/1000ADP DUAL PULSE RESISTANCE WELDING POWER SUPPLY

990-922

3-5

PULSE 1 - ACTION

Press and release the

PULSE 1

button until the

ACTION

parameter is highlighted. Use the

▲▼

arrows to select the desired action.
If

ACTION

is set to

CONTINUE

, Pulse 2 will be

enabled whether or not Pulse 1 is within limits.
If

ACTION

is set to

INHIBIT PULSE 2

, then Pulse 2

will enabled

only

when Pulse 1 is within limits.

RESET WELD COUNTER

From the

LIMITS/COUNTERS

edit screen, press

and release the

LIMITS/COUNTERS

button until

the weld counter field is highlighted.
Press the

CLEAR

key to clear the weld counter to

000000

NOTE:

The weld counter value can

not

changed using the

▲▼

arrows.

EDIT COUNTER LIMIT

From the

LIMITS/COUNTERS

edit screen, press

and release the

LIMITS/COUNTERS

button until

the

COUNTER LIMIT

field is highlighted.

Press the

▲▼

arrows to set a desired limit

value or use the

CLEAR

key to reset to the limit

000000.

Setting the

counter limit to

000000

will disable the

WELD COUNTER RELAY

output signal available

at the rear panel

37-PIN I/O CONNECTOR

Содержание 1000ADP

















































































































Результаты поиска

Содержание 1000ADP

Отзывы:

Бренды по названию

Популярные бренды

Amada 1000ADP, Руководство по эксплуатации

Результаты поиска

Содержание 1000ADP

Отзывы:

Бренды по названию

Популярные бренды