manualshive.com logo in svg

Altigen AltiWare ACM 5.1, Руководство администратора

Administration Manual для Altigen AltiWare ACM 5.1 доступен для бесплатного скачивания на manualshive.com. Получите подробное руководство по управлению продуктом, включая инструкции по настройке и обслуживанию. Скачайте его прямо сейчас, чтобы максимально эффективно использовать ваше оборудование.

Поделиться
Скачать
background image

Chapter 12:  Trunk Configuration

AltiWare ACM 5.1 Administration Manual 155

SIP Trunk Properties 

Traditionally telecom trunks are from your local carrier’s PSTN switch and the dial tone 
is provided via either analog trunks or T1/PRI digital trunks. A new type of service called 
“IP Dial Tone,” which allows you to dial a long distance call at a lower rate, is available. 
IP Dial Tone is delivered through your IP data network, and the service provider can be 
anywhere in the world, as long as the VoIP data packets can be routed properly.
If you have SIP-based IP dial tone service from an Internet Telephony Service Provider 
(ITSP), you need to configure SIP trunk channels to connect the service. Before you 
start, note the following:

•

An AltiGen SIP Trunking channel is licensed. You need to buy and register a license 
to be able to configure this option.

•

AltiGen does not guarantee the voice quality of the SIP dial tone coming from your 
service provider. You need to work with your data service and SIP trunking service 
provider to make sure adequate QoS is provisioned for your WAN service.

•

AltiGen does not guarantee SIP trunk implementation will work with all SIP Dial Tone 
service providers. You need to verify that your SIP Dial Tone service provider 
supports the following:

•

G.711, G.723.1, G.729 codec

•

RFC 2833 for DTMF tone delivery

•

SIP MD5 authentication with SIP registration

•

If AltiServ is behind NAT, verify that your SIP SP can support this configuration.

When subscribing to SIP Dial Tone service, typically your service provider will provide 
you with the information required in the configuration dialog box shown in Figure 5 on 
page 156. Enter these service parameters to each SIP trunk channel configuration 
individually.

Note:

This is signal only trunks. Make sure you have enough IP resource boards to cover 
your needs.

Important:

You need to add the SIP Trunk service provider’s IP address to the IP Device 
Range in AltiEnterprise Manager and select the proper codec profile for this 
service. See “Assigning Codec Profiles to IP Addresses” on page 330. Failure 
to do this step may cause no voice path, even if the SIP Trunk channel shows 
the call is connected.

Configuring a SIP Trunk

To open a trunk configuration dialog box for a SIP trunk, do one of the following:

•

In the Trunk Configuration window, select a SIP trunk type, click the Trunk 
Properties button, then click the SIP Trunk Configuration button.

•

In the Board View window, double-click a SIPSP board type, click the Board 
Configuration button, then click the SIP Trunk Configuration button.

Содержание AltiWare ACM 5.1







































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AltiWare ACM 5.1

NEC NP-PH1400U Manual preview
NP-PH1400U
Бренд: NEC Страницы: 3
Yamaha MOTIF RACK ES Supplementary Manual preview
MOTIF RACK ES
Бренд: Yamaha Страницы: 37
Extreme Networks ExtremeWare Enterprise Manager Installation And User Manual preview
ExtremeWare Enterprise Manager
Бренд: Extreme Networks Страницы: 264
Q-See Remote Client Software V 4.0.1 User Manual preview
Remote Client Software V 4.0.1
Бренд: Q-See Страницы: 72
Adobe 65014293 - Photoshop CS4 - Mac Manual preview
65014293 - Photoshop CS4 - Mac
Бренд: Adobe Страницы: 87
ACRONIS ADVANCED SERVER Datasheet preview
ADVANCED SERVER
Бренд: ACRONIS Страницы: 2
FARONICS INSIGHT - Manual preview
INSIGHT -
Бренд: FARONICS Страницы: 43
Sun Microsystems Sun GlassFish EnterpriseServer v3 Prelude Troubleshooting Manual preview
Sun GlassFish EnterpriseServer v3 Prelude
Бренд: Sun Microsystems Страницы: 48
Sun Microsystems Sun StorEdge Availability Suite 3.2 Troubleshooting Manual preview
Sun StorEdge Availability Suite 3.2
Бренд: Sun Microsystems Страницы: 52
AVG ANTI-VIRUS 2011 - REV 2011.11 User Manual preview
ANTI-VIRUS 2011 - REV 2011.11
Бренд: AVG Страницы: 209
Tektronix PhaserPrint 2.0 Configuration Manual preview
PhaserPrint 2.0
Бренд: Tektronix Страницы: 2
Intel Application Accelerator RAID Edition User Manual preview
Application Accelerator RAID Edition
Бренд: Intel Страницы: 85
Universal Audio UAD User Manual preview
UAD
Бренд: Universal Audio Страницы: 585
MINOLTA-QMS ImageServer User Manual preview
ImageServer
Бренд: MINOLTA-QMS Страницы: 42
MACROMEDIA CONTRIBUTE 3 - DEPLOYING AND PUBLISHING SERVER Manual preview
CONTRIBUTE 3 - DEPLOYING AND PUBLISHING SERVER
Бренд: MACROMEDIA Страницы: 38
KAPERSKY ANTI-VIRUS - FOR SUN SOLARIS MAIL SERVER User Manual preview
ANTI-VIRUS - FOR SUN SOLARIS MAIL SERVER
Бренд: KAPERSKY Страницы: 254
IVT BlueSoleil User Manual preview
BlueSoleil
Бренд: IVT Страницы: 49
Datalogic PDA User Manual preview
PDA
Бренд: Datalogic Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды