manualshive.com logo in svg

Altera Stratix V Hard IP, Руководство пользователя, Страница: 55 / 232

Поделиться
Скачать
Altera Stratix V Hard IP Скачать руководство пользователя страница 55

Chapter 4: Parameter Settings

4–3

System Settings

June 2012

Altera Corporation

Stratix V Hard IP for PCI Express

User Guide

RX Buffer credit 
allocation -
performance for 
received requests 

(continued)

High

Maximum

■

High

–This setting configures most of the RX Buffer space for 

received requests and allocates a slightly larger than minimum 
amount of space for received completions. Select this option where 
most of the PCIe requests are generated by the other end of the PCIe 
link and the local application layer logic only infrequently generates a 
small burst of read requests. This option is recommended for typical 
root port applications where most of the PCIe traffic is generated by 
DMA engines located in the endpoints. 

■

Maximum

–This setting configures the minimum PCIe specification 

allowed amount of completion space, leaving most of the RX Buffer 
space for received requests. Select this option when most of the PCIe 
requests are generated by the other end of the PCIe link and the local 
application layer logic never or only infrequently generates single 
read requests. This option is recommended for control and status 
endpoint applications that don't generate any PCIe requests of their 
own and only are the target of write and read requests from the root 
complex.

Reference clock 
frequency

100 MHz
125 MHz

The 

PCI Express Base Specification 3.0 

requires a 

100 MHz

±

300 ppm reference clock. The 125 MHz reference clock is 

provided as a convenience for systems that include a 125 MHz clock 
source. For more information about Gen3 operation, refer to “4.3.8 
Refclk Specifications for 8.0 GT/s” in the specification. 

Use 62.5 MHz 
application clock 

On/Off

This is a special power saving mode available only for Gen1 ×1 and Gen2 
×1 variants. 

Use deprecated RX 
Avalon-ST data byte 
enable port (rx_st_be)

On/Off

This parameter is not available for the Avalon-MM Stratix V Hard IP for 
PCI Express.

Enable byte parity 
ports on Avalon-ST 
interface

On/Off

When 

On

, the RX and TX datapaths are parity protected. Parity is odd. 

This parameter is not available for the Avalon-MM Stratix V Hard IP for 
PCI Express.

Multiple packets per 
cycle

On/Off

When 

On

, the 256-bit Avalon-ST interface supports the transmission of 

TLPs starting at any 128-bit address boundary, allowing support for 
multiple packets in a single cycle. To support multiple packets per cycle, 
the Avalon-ST interface includes 2 start of packet and end of packet 
signals for the 256-bit Avalon-ST interfaces. This feature is only 
supported for Gen3 ×8.

For more information refer to 

“Multiple Packets per Cycle” on 

page 6–27

. 

Enable configuration 
via the PCIe link

On/Off

When 

On

, the Quartus II software places the Endpoint in the location 

required for configuration via protocol (CvP). For more information 
about CvP, refer to 

“Configuration via Protocol (CvP)” on page 10–1

.

Enable Hard IP 
Reconfiguration

On/Off

When enabled, you can use the Hard IP reconfiguration bus to 
dynamically reconfigure Hard IP read-only registers. For more 
information refer to 

“Hard IP Reconfiguration Interface” on page 14–1

.

Table 4–2. System Settings for PCI Express (Part 3 of 4)

Parameter

Value

Description

Содержание Stratix V Hard IP









































































































































































































































Отзывы:

Нет отзывов