Altera Stratix V Hard IP Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 232

Altera Stratix V Hard IP Скачать руководство пользователя страница 48

3–10

Chapter 3: Getting Started with the Avalon-MM Stratix V Hard IP for PCI Express

Completing the Connections in Qsys

Stratix V Hard IP for PCI Express

June 2012

Altera Corporation

User Guide

f

For more information about the Transceiver Reconfiguration Controller, refer to the

Transceiver Reconfiguration Controller

chapter in the

Altera Transceiver PHY IP Core User

Completing the Connections in Qsys

In Qsys, hovering the mouse over the

Connections

column displays the potential

connection points between components, represented as dots on connecting wires. A
filled dot shows that a connection is made; an open dot shows a potential connection
point. Clicking a dot toggles the connection status. If you make a mistake, you can
select

Undo

from the Edit menu or type

Ctrl-z

.

By default, Qsys filters some interface types to simplify the image shown on the

System Contents

tab. Complete these steps to display all interface types:

1. Click the

Filter

toolbar button.

2. In the Filter list, select

All interfaces

.

3. Close the

Filters

dialog box.

To complete this design, create the following connections:

1. Connect the pcie_sv_hip_avmm_0

Rxm_BAR0

Avalon Memory-Mapped Master port

to the onchip_memory2_0

s1

Avalon Memory-Mapped slave port using the

following procedure:

a. Click the

Rxm_BAR0

port, then hover in the

Connections

column to display

possible connections.

b. Click the open dot at the intersection of the

onchip_mem2_0

s1

port and the

pci_express_compiler

Rxm_BAR0

to create a connection.

2. Repeat step 1 to make the connections listed in

.

Table 3–11. Qsys Connections

Make Connection From:

To:

pcie_sv_hip_avmm_0

nreset_status

Reset Output

onchip_mem

reset1

Avalon slave port

pcie_sv_hip_avmm_0

nreset_status

Reset Output

dma_0

reset

Reset Input

pcie_sv_hip_avmm_0

nreset_status

Reset Output

alt_xcvr_reconfig_0

mgmt_rst_reset

Reset Input

pcie_sv_hip_avmm_0

Rxm_BAR2

Avalon Memory Mapped

Master

pcie_sv_hip_avmm_0

Cra

Avalon Memory Mapped Slave

pcie_sv_hip_avmm_0

Rxm_BAR2

Avalon Memory Mapped

Master

dma_0

control_port_slave

Avalon Memory Mapped

Slave

pcie_sv_hip_avmm_0

RxmIrq

Interrupt Receiver

dma_0

irq

Interrupt Sender

pcie_sv_hip_avmm_0

reconfig_to_xcvr

Conduit

alt_xcvr_reconfig_0

reconfig_to_xcvr

Conduit

pcie_sv_hip_avmm_0

reconfig_busy

Conduit

alt_xcvr_reconfig_0

reconfig_busy

Conduit

pcie_s_hip_avmm_0

reconfig_from_xcvr

Conduit

alt_xcvr_reconfig_0

reconfig_from_xcvr

Conduit

pcie_sv_hip_avmm_0

Txs

Avalon Memory Mapped Slave

dma_0

read_master

Avalon Memory Mapped Master

pcie_sv_hip_avmm_0

Txs

Avalon Memory Mapped Slave

dma_0

write_master

Avalon Memory Mapped Master

onchip_memory2_0

s1

Avalon Memory Mapped Slave

dma_0

read_master

Avalon Memory Mapped Master

«
...
46
47
48
49
50
...
»

Содержание Stratix V Hard IP









































































































































































































































Отзывы:

Нет отзывов