Altera Stratix V Hard IP Скачать руководство пользователя страница 26

Страница: 26 / 232

2–8

Chapter 2: Getting Started with the Stratix V Hard IP for PCI Express

MegaWizard Plug-In Manager Design Flow

Stratix V Hard IP for PCI Express

June 2012

Altera Corporation

User Guide

Figure 2–3

illustrates this Qsys system.

4. To display the parameters of the

APPS

component shown in

Figure 2–3

, click on it

and then select

Edit

from the right-mouse menu.

Figure 2–4

illustrates this

component. Note that the values for the following parameters match those set in
the DUT component:

■

Targeted Device Family

■

Lanes

■

Lane Rate

■

Application Clock Rate

■

Port type

■

Application interface

■

Tags supported

■

Maximum payload size

■

Number of Functions

Figure 2–3. Qsys System Connecting the Endpoint Variant and Chaining DMA Testbench

Содержание Stratix V Hard IP









































































































































































































































Результаты поиска

Содержание Stratix V Hard IP

Отзывы:

Altera Stratix V Hard IP, Руководство пользователя, Страница: 26 / 232

Результаты поиска

Содержание Stratix V Hard IP

Отзывы: