Allied 95G1UHE Скачать руководство пользователя

Страница: 48 / 59

508093-01

Issue 2033

Page 48 of 59

Furnace should operate at least 5 minutes before checking

gas flow. Determine time in seconds for two revolutions of

gas through the meter. (Two revolutions assures a more

accurate time.) Divide by two and compare to time in Table

16. If manifold pressure matches Table 18 and rate is

incorrect, check gas orifices for proper size and restriction.

Remove temporary gas meter if installed.

NOTE:

To obtain accurate reading, shut off all other gas

appliances connected to meter.

Supply Pressure Measurement

When testing supply gas pressure, use the 1/8” N.P.T.

plugged tap located on the gas valve to facilitate test gauge

connection. See Figure 53. Check gas line pressure with

unit firing at maximum rate. Low pressure may result in

erratic operation or underfire. High pressure can result in

permanent damage to gas valve or overfire.

On multiple unit installations, each unit should be checked

separately, with and without other units operating. Supply

pressure must fall within range listed in Table 18.

Manifold Pressure Measurement

Follow the steps below and use Figure 55 as a reference.

Gas manifold Kit 10L34 provides additional components if

needed.

Connect the test gauge positive side “+“ to manifold

pressure tap on gas valve.

Tee into the gas valve regulator vent hose and connect

to test gauge negative “-”.

Start unit and let run for 5 minutes to allow for steady

state conditions.

After allowing unit to stabilize for 5 minutes, record

manifold pressure and compare to value given in

Table 18.

Shut unit off and remove manometer as soon as an

accurate reading has been obtained. Take care to

remove barbed fitting and replace threaded plug.

Start unit and perform leak check. Seal leaks if found.

(+)

(−)

Gas Valve Regulator

Vent Hose

(to burner box)

2” Long Square Tubing

(remove for manifold adjustment)

Tee

10” Long

Square

Tubing

Measuring Device

Barbed Fitting

Manifold Pressure Outlet

Negative Barbed Fitting

(remove for manifold adjustment)

Figure 55.

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды