Allied 95G1UHE Скачать руководство пользователя

Страница: 12 / 59

508093-01

Issue 2033

Page 12 of 59

Figure 3. Integrated Control

(Automatic Hot Surface Ignition System)

BLOWER OFF DELAY

RED LED RECALL BUTTON

Electronic Ignition

On a call for heat the integrated control monitors the

combustion air inducer pressure switch. The control board

will not begin the heating cycle if the pressure switch is

closed (by-passed). Once the pressure switch is determined

to be open, the combustion air inducer is energized. When

the differential in the pressure switch is great enough, the

pressure switch closes and a 15-second pre-purge begins.

If the pressure switch is not proven within 2-1/2 minutes,

the integrated control goes into Watchguard-Pressure

Switch mode for a 5-minute re-set period.

After the 15-second pre-purge period, the ignitor warms

up for 20 seconds during which the gas valve opens at

19 seconds for a 4-second trial for ignition. The ignitor

remains energized for the first 3 seconds during the 4

second trial. If ignition is not proved during the 4-second

period, the integrated control will try four more times with

an inter purge and warm-up time between trials of 35

seconds. After a total of five trials for ignition (including the

initial trial), the integrated control goes into Watchguard-

Flame Failure mode. After a 60-minute reset period, the

integrated control will begin the ignition sequence again.

Fan Time Control

Heating Fan On Time

The fan on time of 30 seconds is not adjustable.

Heating Fan Off Time

Fan off time (time that the blower operates after the heat

demand has been satisfied) can be adjusted by moving

the jumper to a different setting. The unit is shipped with

a factory fan off setting of 90 seconds. For customized

comfort, monitor the supply air temperature once the heat

demand is satisfied. Note the supply air temperature at the

instant the blower is de-energized.

Adjust the fan-off delay to achieve a supply air temperature

between 90° - 110° at the instant the blower is de-energized.

(Longer delay times allow for lower air temperature, shorter

delay times allow for higher air temperature). See Figure 4.

Cooling Fan On Time

The fan on time is 2 seconds and is not adjustable.

Cooling Fan Off Time

The control has a 45 second fan off delay after cooling

demand has been met. This delay is factory set and not

adjustable.

Figure 4.

Heating Components

Combustion air inducer (B6), primary limit control (S10),

ignitor, burners, flame rollout switch (S47), gas valve

(GV1), combustion air pressure switch (S18), and heat

exchangers are located in the heating compartment. The

heating compartment can be accessed by removing the

outer access panel.

Ignitor (Figure 5)

A95UH1E / 95G1UHE units use a nitride ignitor made from

a proprietary ceramic material. To check ignitor, measure

its resistance and voltage. A value of 39 to 70 ohms

indicates a good ignitor. Voltage to the ignitor should be

102 - 132VAC. See Figure 9 for resistance and voltage

checks.

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды