Allied 95G1UHE Скачать руководство пользователя

Страница: 46 / 59

508093-01

Issue 2033

Page 46 of 59

Start-Up

Preliminary and Seasonal Checks

Inspect electrical wiring, both field and factory installed

for loose connections. Tighten as required.

Check voltage at disconnect switch. Voltage must be

within range listed on the nameplate. If not, consult the

power company and have voltage condition corrected

before starting unit.

Inspect condition of condensate traps and drain

assembly. Disassemble and clean seasonally.

Heating Start-Up

BEFORE LIGHTING

the unit, smell all around the furnace

area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

The gas valve on the A95UH1E / 95G1UHE is equipped

with a gas control switch. Use only your hand to move the

switch. Never use tools. If the the switch will not move by

hand, replace the valve. Do not try to repair it. Force or

attempted repair may result in a fire or explosion.

Placing the Furnace Into Operation

A95UH1E / 95G1UHE units are equipped with an ignition

system. Do not attempt to manually light burners on this

furnace. Each time the thermostat calls for heat, the

burners will automatically light. The ignitor does not get hot

when there is no call for heat on units with ignition system.

Priming Condensate Trap

The condensate trap should be primed with water prior

to start-up to ensure proper condensate drainage. Either

pour 10 fl. oz. (300 ml) of water into the trap, or follow

these steps to prime the trap:

Follow the lighting instructions to place the unit into

operation.

Set the thermostat to initiate a heating demand.

Allow the burners to fire for approximately 3 minutes.

Adjust the thermostat to deactivate the heating

demand.

Wait for the combustion air inducer to stop. Set the

thermostat to initiate a heating demand and again

allow the burners to fire for approximately 3 minutes.

Adjust the thermostat to deactivate the heating demand

and again wait for the combustion air inducer to stop.

At this point, the trap should be primed with sufficient

water to ensure proper condensate drain operation.

If you do not follow these instructions exactly, a fire

or explosion may result causing property damage,

personal injury or death.

WARNING

Gas Valve Operation (Figure 53)

STOP!

Read the safety information at the beginning

of this section.

Set the thermostat to the lowest setting.

Turn off all electrical power to the unit.

This furnace is equipped with an ignition device which

automatically lights the burners. Do not try to light the

burners by hand.

Remove the access panel.

Move gas valve switch to OFF. See Figure 53.

Wait five minutes to clear out any gas. If you then

smell gas,

STOP!

Immediately call your gas supplier

from a neighbor’s phone. Follow the gas supplier’s

instructions. If you do not smell gas go to next step.

Move gas valve switch to ON. See Figure 53.

Figure 53. Gas Valve

GAS VALVE SHOWN IN ON POSITION

MANIFOLD

PRESSURE

OUTLET

PORT

INLET

PRESSURE

PORT

MANIFOLD PRESSURE

ADJUSTMENT SCREW

(under barbed fitting)

Replace the access panel.

10.

Turn on all electrical power to to the unit.

11.

Set the thermostat to desired setting.

NOTE:

When unit is initially started, steps 1 through

11 may need to be repeated to purge air from gas line.

12.

If the appliance will not operate, follow the instructions

“Turning Off Gas to Unit” and call your service

technician or gas supplier.

Turning Off Gas to Unit

Set the thermostat to the lowest setting.

Turn off all electrical power to the unit if service is to

be performed.

Remove the access panel.

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды