Allied 95G1UHE Скачать руководство пользователя

Страница: 25 / 59

508093-01

Issue 2033

Page 25 of 59

Promptly apply solvent cement to end of pipe and

inside socket surface of fitting. Cement should be

applied lightly but uniformly to inside of socket. Take

care to keep excess cement out of socket. Apply

second coat to end of pipe.

Immediately after applying last coat of cement to pipe,

and while both inside socket surface and end of pipe

are wet with cement, forcefully insert end of pipe into

socket until it bottoms out. Turn PVC pipe 1/4 turn

during assembly (but not after pipe is fully inserted) to

distribute cement evenly. DO NOT turn ABS or cellular

core pipe.

NOTE:

Assembly should be completed within 20

seconds after last application of cement. Hammer

blows should not be used when inserting pipe.

After assembly, wipe excess cement from pipe at end

of fitting socket. A properly made joint will show a bead

around its entire perimeter. Any gaps may indicate an

improper assembly due to insufficient solvent.

Handle joints carefully until completely set.

Venting Practices

Figure 19. Piping Suspension Guidelines

* See table 10 for allowable pipe.

NOTE

- Isolate piping at the point where it exits the outside wall or

roof in order to prevent transmission of vibration to the structure.

SCHEDULE 40

PVC - 5'

all other pipe* - 3'

Wall

24” maximum

3/4” minimum

Wall Thickness Guidelines

insulation

(if required)

•

In areas where piping penetrates joists or interior walls,

hole must be large enough to allow clearance on all

sides of pipe through center of hole using a hanger.

•

When furnace is installed in a residence where unit

is shut down for an extended period of time, such

as a vacation home, make provisions for draining

condensate collection trap and lines.

Figure 20.

CHIMNEY

OR GAS

VENT

(Check sizing

for water

heater only)

FURNACE

(Replaced

by EL195)

WATER

HEATER

OPENINGS

(To Adjacent

Room)

If the furnace replaces a furnace which

was commonly vented with another gas appliance,

appliance must be checked. Without the heat of the

original furnace flue products, the existing vent pipe

is probably oversized for the single water heater or

other appliance. The vent should be checked for

proper draw with the remaining appliance.

REPLACING FURNACE THAT

WAS PART OF A COMMON

VENT SYSTEM

the size of the existing vent pip for that gas

Exhaust Piping (Figure 23 and Figure 24)

Route piping to outside of structure. Continue with

installation following instructions given in piping termination

section.

Do not discharge exhaust into an existing stack or

stack that also serves another gas appliance. If vertical

discharge through an existing unused stack is required,

insert PVC pipe inside the stack until the end is even

with the top or outlet end of the metal stack.

CAUTION

The exhaust vent pipe operates under positive pressure

and must be completely sealed to prevent leakage of

combustion products into the living space.

CAUTION

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды