Allied 95G1UHE Скачать руководство пользователя

Страница: 18 / 59

508093-01

Issue 2033

Page 18 of 59

Figure 11.

Measuring Pressure Differential

To Cold End Header Box

Field Provided Tubing

To Pressure Switch

To Cold End Header Box

1 - Remove thermostat demand and allow unit to

cycle off.

2 - Install a tee in the negative (-) line (red and black tubing

or red tubing) and a tee in the positive (+) line (black

tubing) running from the pressure switch to the cold

end header box.

3 - Install a manometer with hose from the negative (-)

side of the manometer to the tee installed in the

negative (-) line and with hose from the positive (+)

side of the manometer to the tee in the positive (+)

line.

NOTE -

tive. However the (+) port reads less negative pressure

than the (-) port.

4 - Operate unit and observe manometer reading.

Readings will change as heat exchanger warms.

a. Take one reading immediately after start

‐

up.

b. Take a second reading after unit has reached

steady state (approximately 5 minutes). This will be

the pressure differential.

The pressure differential should be greater

than those listed in table 7.

5 - Remove thermostat demand and allow to cycle off.
6 - Remove manometer and tee's. Reinstall combustion

air sensing hoses to the pressure switch.

Black Tubing

(po)

Red and

Black

Tubing

or Red Tubing

(negative -)

“+”

High

“-”

Low

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды