Allied 95G1UHE Скачать руководство пользователя

Страница: 19 / 59

508093-01

Issue 2033

Page 19 of 59

Problem

Corrective Action

Pressure switch stuck closed

Check that the pressure switch is open without the combustion air inducer

operating. Replace if defective.

Pressure switch does not close due to obstruction in

vent pipe

Check for restricted vent. Remove all blockage.
Check for proper vent sizing. See Table 11 through Table 13.

Pressure switch does not close due to incorrect

routing of the pressure switch tubing

Check that the pressure switch tubing is correctly routed. Correctly route

pressure switch line.

Pressure switch does not close due to obstructions in

the pressure switch line

Remove any obstructions from the the pressure switch line and/or taps

Pressure switch tubing damaged

Check pressure switch tubing for leaks. Replace damaged tubing if

necessary.

Condensate in pressure switch tubing

Check pressure switch tubing for condensate. Remove condensate from

tubing.

Pressure switch does not close due to a low

differential pressure across the pressure switch

Check the differential pressure across the pressure switch.
Check for restricted inlet vent. Remove all blockage.
Check for proper vent sizing and run length. See Table 11 through Table 13.

Wrong pressure switch installed in the unit, or

pressure switch is out of calibration

Check that the correct pressure switch is installed in the unit. Replace

pressure switch if necessary.

Miswiring of furnace or improper connections at

pressure switch

Check for correct wiring and loose connections. Correct wiring and/or replace

any loose connections.

Pressure switch failure

If all the above modes of failure have been checked, the pressure switch

may have failed. Replace pressure switch and determine if unit will operate.

Damaged condensate trap

Check trap for any cracks or damage and replace if necessary.

Cold end header box does not drain properly

Check that the furnace is set properly with a slight tilt (0 - 1/2”) towards the

front if necessary. See furnace installation instruction.

Air leakage around the combustion air inducer gasket

Check gasket and replace if necessary.

Air leakage around the cold end header box gasket

Check gasket and replace if necessary.

Damaged cold end header box tubing

Check tubing and replace if necessary.

Table 7.

Pressure Switch Troubleshooting Guide

Figure 12.

Measuring Pressure Differential

DEMAND

CAI

GAS VALVE

ON
OFF

IGNITOR

Pre -Purge

Ignitor Warm-up

Trial for

Ignition

Post

Purge

5 SEC

*Blower on time will be 30 seconds after flame is sensed. Blower off time will depend on “OFF TIME” Setting.

INDOOR BLOWER

Blower “On”*

Delay

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды