Allied 95G1UHE Скачать руководство пользователя

Страница: 54 / 59

508093-01

Issue 2033

Page 54 of 59

30.

Reinstall the cold end header box.

31.

Reinstall the combustion air inducer. Reconnect the

plug to the wire harness.

32.

Reinstall pressure switches and reconnect pressure

switch wiring.

33.

Carefully connect combustion air pressure switch

tubing from pressure switches to proper ports on cold

end header collector box.

34.

Reconnect condensate drain line to the cold end

header box.

35.

Use securing screws to reinstall flue collar to the top

cap on the furnace. Reconnect exhaust piping and

exhaust drain tubing.

36.

Replace flexible exhaust adapter on combustion air

inducer and flue collar. Secure using two existing hose

clamps.

37.

Reinstall burner box assembly in vestibule area.

Secure burner box assembly to vestibule panel using

four existing screws. Make sure burners line up in

center of burner ports

38.

Reconnect flame roll-out switch wires.

39.

Reconnect sensor wire and reconnect 2-pin plug from

ignitor.

40.

Reinstall gas valve manifold assembly. Reconnect gas

supply line to gas valve.

41.

Reconnect the combustion air intake pipe.

42.

Reinstall burner box cover.

43.

Reconnect wires to gas valve.

44.

Replace the blower compartment access panel.

45.

Reconnect gas supply piping. Turn on power and gas

supply to unit.

46.

Follow lighting instructions on unit nameplate to light

and operate furnace for 5 minutes to ensure the

furnace is operating properly.

47.

Check all piping connections, factory and field, for gas

leaks. Use a leak detecting solution or other preferred

means.

48.

Replace heating compartment access panel.

Some soaps used for leak detection are corrosive to

certain metals. Carefully rinse piping thoroughly after

leak test has been completed. Do not use matches,

candles, flame or other sources of ignition to check for

gas leaks.

CAUTION

Cleaning the Burner Assembly (if needed)

Turn off electrical and gas power supplies to furnace.

Remove upper and lower furnace access panels.

Disconnect the wires from the gas valve.

Remove the burner box cover (if equipped).

Disconnect the gas supply line from the gas valve.

Remove gas valve/manifold assembly.

Mark and disconnect sensor wire from the sensor.

Disconnect wires from flame rollout switches.

Disconnect combustion air intake pipe. It may be

necessary to cut the existing pipe to remove burner

box assembly.

Remove four screws which secure burner box

assembly to vest panel. Remove burner box from the

unit.

Use the soft brush attachment on a vacuum cleaner

to gently clean the face of the burners. Visually

inspect the inside of the burners and crossovers for

any blockage caused by foreign matter. Remove any

blockage.

Reinstall the burner box assembly using the existing

four screws. Make sure that the burners line up in the

center of the burner ports.

10.

Reconnect the sensor wire and reconnect the 2-pin

plug to the ignitor wiring harness. Reconnect wires to

flame rollout switches.

11.

Reinstall the gas valve manifold assembly. Reconnect

the gas supply line to the gas valve. Reinstall the

burner box cover.

12.

Reconnect wires to gas valve.

13.

Replace the blower compartment access panel.

14.

Refer to instruction on verifying gas and electrical

connections when re-establishing supplies.

15.

Follow lighting instructions to light and operate furnace

for 5 minutes to ensure that heat exchanger is clean

and dry and that furnace is operating properly.

16.

Replace heating compartment access panel.

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды