Allied 95G1UHE Скачать руководство пользователя

Страница: 9 / 59

508093-01

Issue 2033

Page 9 of 59

Electrical

ELECTROSTATIC DISCHARGE (ESD)

Precautions and Procedures

Electrostatic discharge can affect electronic

components. Take precautions to

neutralize electrostatic charge by touching

your hand and tools to metal prior to

handling the control.

CAUTION

A95UH1E / 95G1UHE unit components are shown in

Figure 1. The combustion air inducer, gas valve and

burners can be accessed by removing the outer access

panel. The blower and control box can be accessed by

removing the blower access panel.

Control Box Components (Figure 2)

Unit transformer (T1) and integrated ignition control

(A92) are located in the control box. In addition, a door

interlockswitch (S51) is located in the control box.

Integrated Control

Door Interlock

Switch

Transformer

Circuit Breaker

Figure 2. Control Box

Transformer (T1)

A transformer located in the control box provides power

to the low voltage section of the unit. The transformers on

all models are rated at 40VA with a 120V primary and 24V

secondary.

Door Interlock Switch (S51)

A door interlock switch rated 14A at 120VAC is located

on the control box. The switch is wired in series with line

voltage. When the blower door is removed the unit will shut

down.

Circuit Breaker (CB8)

A 24V circuit breaker is also located in the control box. The

switch provides overcurrent protection to the transformer

(T1). The breaker is rated at 3A at 32V. If the current

exceeds this limit the breaker will trip and all unit operation

will shutdown. The breaker can be manually reset by

pressing the button on the face.

Integrated Ignition Control (A92)

Shock hazard.
Disconnect power before servicing.

Control is not field repairable. If control is

inoperable, simply replace entire control.
Can cause injury or death. Unsafe

operation will result if repair is attempted.

WARNING

The hot surface ignition control system consisting of

an integrated control (Figure 3 with control terminal

designations in Table 1 through Table 3), sensor and

ignitor (Figure 5). The integrated control and ignitor work

in combination to ensure furnace ignition and ignitor

durability. The integrated control, controls all major furnace

operations. The integrated control also features a RED

LED for troubleshooting and two accessory terminals rated

at (1) one amp. See Table 4 or Table 5 for troubleshooting

diagnostic codes. The nitride ignitor is made from a non-

porous, high strength proprietary ceramic material that

provides long life and trouble free maintenance.

Pin #

Function

Combustion Air Inducer Line

Ignitor Line

Combustion Air Inducer Neutral

Ignitor Neutral

Table 1.

4-Pin Terminal Designations

Pin #

Function

High Limit Output

Not Used

24V Line

Not Used

Rollout Switch Out

24V Neutral

High Limit Input

Ground

Gas Valve Common

Pressure Switch In

Rollout Switch In

Gas Valve Out

Table 2.

12-Pin Terminal Designations

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды