Allied 95G1UHE Скачать руководство пользователя

Страница: 49 / 59

508093-01

Issue 2033

Page 49 of 59

Proper Combustion

Furnace should operate minimum 15 minutes with correct

manifold pressure and gas flow rate before checking

combustion. Take combustion sample beyond the flue

outlet and compare to Table 17.

Capacity

% for Nat

% for L.P.

All

7.2 - 7.9

8.6 - 9.3

The maximum carbon monoxide reading should not exceed

100 ppm.

Table 17.

High Altitude

NOTE:

In Canada, certification for installations at

elevations over 4500 feet (1372 m) is the jurisdiction of

local authorities.

Some units installed at altitude of 4501 - 10,000 feet

(1373 to 3048 m) may require a pressure switch change

which can be ordered separately and a manifold de-rate.

See Table 18 or Table 19 for manifold pressures at all

altitudes. Table 20 lists conversion kit and pressure switch

requirements at varying altitudes.

The combustion air pressure switch is factory-set and

requires no adjustment.

Unit

Fuel

Manifold

Pressure

Supply Line

All

Nat

3.5

4.5 - 13.0

All

LP/Propane

10.0

11.0 - 13.0

NOTE - A natural to L.P. propane gas changeover kit is

necessary to convert this unit. Refer to the changeover kit

installation instruction for the conversion procedure.

Table 18.

Supply Line and Manifold Pressure at All

Altitudes (inches w.c.) for -1 Through -3 Units

Capacity

Gas

Manifold Pressure in. w.g.

Supply Line Pressure

in. w.g.

0-10,000 ft.

0-4500 ft.

4501-5500 ft.

5501-6500 ft.

6501-7500 ft. 7501-10000 ft.

All Sizes

Natural

3.5

3.3

3.2

3.1

3.5

4.5

13.0

LP /

Propane

10.0

9.4

9.1

8.9

10.0

11.0

13.0

NOTE

: A natural to LP propane gas changeover kit is necessary to convert this unit. Refer to the changeover kit installation

instruction for the conversion procedure.

Table 19.

Manifold and Supply Line Pressure 0-10,000 ft.

Capacity

0-7,500 ft

(0-2,286m)

7,501 - 10,000 ft

(2,286 - 3,048 m)

Natural to LP/Propane

LP/Propane to Natural

High Altitude Natural

Burner Orifice Kit

High Altitude LP/Propane

Burner Orifice Kit

030

17H62+

N/A

17H90+

045

11K50+

73W80*

51W01

11K45+

070
090

110

135

* Conversion requires installation of a gas valve regulator spring which is provided with the gas conversion kit.
+ LP Kits include low line pressure switch.

Table 20.

Burner Orifice Conversion Kits at Varying Altitudes

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды