Allied 95G1UHE Скачать руководство пользователя

Страница: 47 / 59

508093-01

Issue 2033

Page 47 of 59

Move gas valve switch to OFF.

Replace the access panel.

Failure To Operate

If the unit fails to operate, check the following:

Is the thermostat calling for heat?

Are access panels securely in place?

Is the main disconnect switch closed?

Is there a blown fuse or tripped breaker?

Is the filter dirty or plugged? Dirty or plugged filters will

cause the limit control to shut the unit off.

Is gas turned on at the meter?

Is the manual main shut-off valve open?

Is the internal manual shut-off valve open?

Is the unit ignition system in lockout? If the unit locks

out again, inspect the unit for blockages.

Heating System Service Checks

C.S.A. Certification

All units are C.S.A. design certified without modifications.

Refer to the A95UH1E / 95G1UHE Operation and

Installation Instruction.

Gas Piping

If a flexible gas connector is required or allowed by

the authority that has jurisdiction, black iron pipe shall

be installed at the gas valve and extend outside the

furnace cabinet. The flexible connector can then be

added between the black iron pipe and the gas supply

line.

CAUTION

Do not over torque (800 in-lbs) or under torque (350

in-lbs) when attaching the gas piping to the gas valve.

WARNING

Gas supply piping should not allow more than 0.5” W.C.

drop in pressure between gas meter and unit. Supply gas

pipe must not be smaller than unit gas connection.

Compounds used on gas piping threaded joints should be

resistant to action of liquefied petroleum gases.

Testing Gas Piping

In case emergency shutdown is required, turn off the

main shut-off valve and disconnect the main power to

unit. These controls should be properly labeled by the

installer.

IMPORTANT

When pressure testing gas lines, the gas valve must be

disconnected and isolated. Gas valves can be damaged if

subjected to more than 0.5 psig (14” W.C.). See Figure 54.

Figure 54.

MANUAL MAIN SHUT-OFF

VALVE WILL NOT HOLD

NORMAL TEST PRESSURE

CAP

FURNACE

ISOLATE

GAS VALVE

1/8” N.P.T. PLUGGED TAP

When checking piping connections for gas leaks, use

preferred means. Kitchen detergents can cause harmful

corrosion on various metals used in gas piping. Use of a

specialty Gas Leak Detector is strongly recommended.

Do not use matches, candles, flame or any other source

of ignition to check for gas leaks.

WARNING

Testing Gas Supply Pressure

Gas Flow (Approximate)

Capacity

Seconds for One Revolution

Natural

1 cu ft

Dial

2 cu ft

Dial

1 cu ft

Dial

2 cu ft

Dial

-30

120

240

300

600

-45

160

200

400

-70

110

136

272

-90

102

204

-110

164

-135

136

Natural-1000 btu/cu ft LP-2500 btu/cu ft

Table 16. Gas Meter Clocking Chart

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды