End of Cycle Mode
The control enters this mode when a cycle is complete and the
door is unlocked.
The display shows "Cycle Complete" and time since completion,
if programmed. If programmed, the display shows an advertise-
ment image on half of the screen.
The control enters
when loading door is opened or
valid keypad is pressed.
Door Unlocking Mode
The control enters this mode after a cycle has ended or when en-
tering
. The control displays the Please Wait menu
and waits for confirmation that the door is unlocked. Once confir-
mation is received that door is unlocked, the control enters
if cycle time remaining,
if desired from
, or
Factory Test Mode
The user can enter this mode via the keypad (if enabled, refer to
) or the IrDA device from
,
, or through manual diagnostics.
While in Factory Test Mode the machine cycles through test steps
and displays. Refer to
for more information.
Lockout Mode
This mode is entered to prevent the machine from being used ex-
cept by a particular user who has reserved the machine in ad-
vance. This mode is entered when the current time (in hours and
minutes) falls within the time period set by the Lockout Mode
Start Time Hour, Lockout Mode Start Time Minute and Lockout
Duration and when the control is in
display "Lockout" and "We apologize for the inconvenience".
When any valid key is pressed the Passcode Menu will be shown.
The user will be able to enter the passcode. If the passcode is en-
tered correctly, the control will enter Ready Mode. If the pass-
code is entered incorrectly, the control will remain in Lockout
Mode and revert to showing the "Lockout" display.
User access is ignored until Lockout Mode is exited. The control
will be able to communicate with the network, IR, or the serial
payment system. If the control was in
at the time the
Lockout Mode was programmed to start, the control will wait un-
til the machine cycle ends to enter Lockout Mode from
if the current time still falls within the Lockout Duration.
Lockout Mode can be exited by a network or IR command, a
time-out, or by entering the correct programmed passcode into
the control.
If the network programs the duration to zero, Lockout Mode will
be exited. If the coin vault is opened and the keypad is press-
ed, the control will go to the
.
NOTE:
are not available during Lockout Mode.
Drop-Off Mode
If enabled (refer to
), Drop-Off Mode allows the
owner to limit machine use to an attendant without requiring
vend. The control displays "Drop-Off" and "We apologize for the
inconvenience". All coin and start pulse inputs are ignored. The
control can communicate with the Network, the IR, or Card
Reader and any time while in Drop-Off Mode. If enabled by the
owner (refer to
in Drop-Off Mode.
When any valid keypad is pressed the Passcode Menu will be
shown. The user will be able to enter the passcode. If the pass-
code is entered correctly, the control will enter Start Mode. If the
passcode is entered incorrectly, the control will remain in Drop-
Off Mode and revert to showing the "Drop-Off" display.
The control remains in Drop-Off Mode until canceled (refer to
Overflow Mode
The control enters this mode when the control detects the water
level is too high. If enabled (refer to
shows "Overflow" and "We apologize for the inconvenience".
If running a cycle, the machine will drain until the water level is
below the overflow reset level. If not in a cycle, the machine will
drain until the drum is empty.
With the door locked, if the water level drops below the overflow
level within five minutes of first detecting the overflow, the cycle
will continue as normal. If the control continues to see an over-
flow level after five minutes with the door locked, the control
will enter Machine Error Mode with an Overflow Error. If the
door is open or is unable to lock, and the water level does not
drop below overflow level after one minute, the control will enter
Machine Error Mode with an Overflow Error.
All vending inputs will be ignored during this mode.
Shutdown Mode
If this programmable option is enabled, the control enters Shut-
down Mode at the start date and time set by the owner. The con-
trol will remain in Shutdown Mode until the end date and time set
by the owner. The control will display “Shutdown” and “We
apologize for the inconvenience.” All keypad presses will be ig-
nored.
Machine Error Mode
The control enters this mode when an error is set and displays all
alarms and machine errors.
Pause Mode
If enabled (refer to
), the user can put the control in
Pause Mode within the first three (3) minutes of a cycle. This is
useful if an article of laundry needs to be added to the current
wash load or if the incorrect cycle was selected.
Control Identification
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14
Part No. 806526ENR2
Содержание Quantum Platinum
Страница 2: ......
