If the control is in Ready Mode with the
displayed and the loading door closed, pressing the keypad
changes the control displays the Please Pay Menu.
If the user enters additional vend or selects a different cycle with
a vend price less than or equal to the vend entered, the control en-
ters
and the remaining funds, if any, are reallocated to
an extra vend.
Partial Vend Mode
The control is in this mode when part of the vend price is entered,
but the full current vend price is not yet satisfied. The display
shows the
. If the user presses the key-
pad before satisfying the vend, the display shows "Please Pay"
and "Or press any button to change your selections".
If the user enters additional vend or selects a different cycle with
a vend price less than or equal to the vend entered, the control en-
ters
and the remaining funds, if any, are reallocated to
an extra vend.
Additional Vend Mode
The control enters Additional Vend Mode if the user selects a dif-
ferent cycle/modifier with a vend price greater than the vend en-
tered and prior to the first fill level being reached. The display
shows the
with the added time and addi-
tional vend required. If no action is taken within sixty (60) sec-
onds, the control reverts back to the original cycle and the previ-
ous mode. The sixty (60) second timer resets if the user enters ad-
ditional vend. Satisfying the additional vend price or pressing the
keypad reverts the control back to the original cycle/modifier
selection and immediately resumes the cycle.
OPL Mode
or via IrDA or network communica-
tions, the owner can enable and disable the machine to run cycles
without vend. Press the keypad to start the machine cycle. The
owner can enable the use of Rapid Advance (refer to
) in OPL Mode.
Delayed Start Mode
Delayed Start Mode can be used only is OPL Mode is active.
The control enters Delayed Start Mode after the user activates a
delayed start from the
shows a countdown (HH:MM:SS) until the machine automatical-
ly starts the selected cycle.
The control enters the Delayed Start Final Countdown Menu dur-
ing the last 60 seconds before the machine automatically starts
the selected cycle. Pressing the keypad starts the selected cy-
cle immediately.
Door Locking Mode
The control enters this mode if the door is closed and after the
keypad is pressed in
a cycle. The control shows "Please Wait" on the display and stays
in the Door Locking Mode until it confirms the loading door is
closed and locked. The control enters
If the door is opened, the control shows the
Start Mode
The control enters this mode when the full vend price is satisfied,
the vend price is zero (0) or if the control is in
or
. In this mode, the machine is ready to start a cy-
cle. Pressing the keypad puts the control in
saves the hour and minute of the day the cycle was started in
. The control enters Start Mode when in
),
the control cycles the audio signal (1 second on/off) for the first
10 seconds of the Start Mode.
Any cycle selection keypad press changes the display to
. The keypad starts the selected cycle or, if
and any of the default cycles are
reprogrammed, the cycle selection is set to the default cycle. If
the control is not in
, the default cycle selection is not
loaded until the next time the control enters Start Mode. If the
control is in
and the cycles programming parameters
are updated, the updated cycles are loaded immediately. If the
control is not in
, the cycle programming parameters
are not updated unless the current cycle key is pressed. If the con-
trol is in
and the OPL Programming Parameter is dis-
abled, the control reverts back to
Advertisement Display Mode
In Advertisement Display Mode, the control cycles through a ser-
ies of advertisement images at a determined rate (refer to the Ad-
vertisement Image Index Rate in
, after 4.25 minutes of no user input, every other display
shows an advertisement. Between each advertisement, the display
shows the coin denomination slide and/or programmed payment
methods. Any keypress changes the display to the
. The advertisement shows on only half the screen while in
tisement images via network communications.
Run Mode
The control enters Run Mode during a cycle. The display shows
the
. The loading door is closed and locked during Run
if the loading door
unlocks or opens.
If a selection keypad is pressed, the
will
. It will display the currently running
cycle.
The cycle can be changed before the first fill is complete. The
will return after 60 seconds or the keypad is press-
ed.
Control Identification
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13
Part No. 806526ENR2
Содержание Quantum Platinum
Страница 2: ......
