Alliance Laundry Systems UY350 PROFORM TOUCH Скачать руководство пользователя страница 29

Страница: 29 / 63

Tightening Requirement

Bolt

Torque, lb. ft [Nm]

M16 x 160, refer to

Figure 7

155 [210]

Anchoring bolt, refer to

Figure 14

and

Figure 15

29.5 [40]

Threaded rod, refer to

Figure 14

98 [133]

Table 12

Machine Anchoring with Forward Tilting

1. Drill a hole for the anchoring bolt based on the required ma-

chine placement, refer to

Figure 14

Figure 15

45 - 60 kg / 450 - 600 L Models with Forward Tilting
and without Weighing System - Drilling Points for
Anchoring Bolts

CZW11N

Threaded rod M14 x 120 and chemical filling are not sup-
plied with the machine

Anchoring bolt (supplied with the machine)

Figure 14

Machine Anchoring with Forward Tilting and

without Weighing System

Machine 45 - 60 kg / 450 - 600 L

Specification

Requirement, in.

[mm]

0.63 [16 ]

0.63 [16]

51.69 [1313]

4.55 [115.5]

0.59 [15]

5.51 [140]

27.26 [692.5]

0.59 [15]

41.57 [1056]

3.94 [100]

9.65 [245]

Table 13

Installation

DO NOT COPY or TRANSMIT

Part No. D2601EN

Содержание UY350 PROFORM TOUCH
































































Результаты поиска

Содержание UY350 PROFORM TOUCH

Отзывы:

Похожие инструкции для UY350 PROFORM TOUCH

Бренды по названию

Популярные бренды

Alliance Laundry Systems UY350 PROFORM TOUCH, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание UY350 PROFORM TOUCH

Отзывы:

Похожие инструкции для UY350 PROFORM TOUCH

Бренды по названию

Популярные бренды