Alliance Laundry Systems UY350 PROFORM TOUCH Скачать руководство пользователя страница 60

Страница: 60 / 63

35 - 60 kg / 350 - 600 L Models, view from above

CZW25N

Screwdriver or other tool

Latch mechanism

Finger protection

Finger protection hole

Lock cover

Figure 48

3. The latch mechanism is lifted up and the lock is unblocked.

The lock stays unblocked even after the tool removal.

4. Open the door if all safety conditions are fulfilled.

Maintenance of Tilting Mechanism

Forward Tilting

Washer Frame

Upper Position Switch

Lower Position Switch

Guiding Plate and Slot

Air Spring

Mechanical Tilt Timer

Screwing of Air Spring

Figure 49

Weekly

1. During the tilting process, inspect the position of the washing

machine to the bearing housing. There should be identical
gaps on both sides. Verify the condition of drain hoses, paying
special attention to where they bend.

2. Inspect pressure setting on washing machine regulator.

Monthly

1. Inspection of the raid of the lower and upper position

switches, adjust if necessary.

2. Inspect the air spring to ensure it is without surface damage.

Also inspect the air supply fitting and hose.

3. Inspect screws of the guide plate and lower stop. Verify their

position and tightness.

4. Inspect tightness of the two lock

‐

nuts on mechanical pulling

rod (safety stop mechanism of tilting function).

NOTE: The parts are accessible upon removal of the
rear part of the lower housing. Refer to

Figure 49

Care of Stainless Steel

• Remove dirt and grease with detergent and water. Thoroughly

rinse and dry after washing.

• Avoid contact with dissimilar metals to prevent galvanic cor-

rosion when salty or acidic solutions are present.

• Do not allow salty or acidic solutions to evaporate and dry on

stainless steel. Wipe clean of any residues.

Maintenance

DO NOT COPY or TRANSMIT

Part No. D2601EN

Содержание UY350 PROFORM TOUCH
































































Результаты поиска

Содержание UY350 PROFORM TOUCH

Отзывы:

Похожие инструкции для UY350 PROFORM TOUCH

Бренды по названию

Популярные бренды

Alliance Laundry Systems UY350 PROFORM TOUCH, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание UY350 PROFORM TOUCH

Отзывы:

Похожие инструкции для UY350 PROFORM TOUCH

Бренды по названию

Популярные бренды