Alliance Laundry Systems UY350 PROFORM TOUCH Скачать руководство пользователя страница 32

Страница: 32 / 63

9. Check and, if necessary, adjust the height of the load sensor

feet so that an even load distribution among all the load sen-
sors is ensured. Refer to

Figure 20

Load Sensors Display

X1, X2, X3, X4 - range must be within 10-40 percentages.

Y1, Y2, Y3, Y4 - load of each load sensor in kilograms.

Figure 20

10. If the load sensors are outside of the specified range, it is nec-

essary to adjust the leveling legs of load sensors. Each load
sensor leveling leg can be adjusted within the range of 0.2 in.
[5 mm].
a. Lift up the machine.
b. Loosen the nut and turn the level leg in order to achieve

the required position.

c. Tighten the nut.
d. Put the machine down and verify that the load applied to

each sensor is within the specified range.

Putting Machine into Service

WARNING

The shipping braces must be removed prior to put-
ting the machine into service. Failure to do so can
result to machine damage.

C204

35 - 45 - 60 kg / 350 - 450 - 600 L Models

1. Remove the three striking color shipping braces securing the

vibrating machine components during the transport.

2. One brace is located in the front part of the machine accessi-

ble after removal of the front lower cover, refer to

Figure 21

Shipping Brace Removal

CZW14NA

Shipping brace

Figure 21

3. Two braces are at the rear of the machine, accessible after re-

moval of the rear cover.

4. After removing the braces, mount the covers back to their pla-

ces.

45 - 60 kg / 450 - 600 L Models with Tilting

1. Place two backstops (supplied with the machine) in their pla-

ces, refer to

Figure 22

Installation

DO NOT COPY or TRANSMIT

Part No. D2601EN

Содержание UY350 PROFORM TOUCH
































































Результаты поиска

Содержание UY350 PROFORM TOUCH

Отзывы:

Похожие инструкции для UY350 PROFORM TOUCH

Бренды по названию

Популярные бренды

Alliance Laundry Systems UY350 PROFORM TOUCH, Установка, эксплуатация и обслуживание

Результаты поиска

Содержание UY350 PROFORM TOUCH

Отзывы:

Похожие инструкции для UY350 PROFORM TOUCH

Бренды по названию

Популярные бренды