• TEMPERATURE IN WASHING MACHINE TUB: The elec-
tronic controller uses the temperature sensor in the tub to con-
trol the temperature of the washing bath. There are a lot of
things that have influence on the temperature measurement.
Therefore the temperature control of the washing bath is not
very precise.
• Always strictly comply with the instructions that are written
on the laundry chemicals-, laundry aids-, dry-cleaning sol-
vents- and disinfectants packaging to avoid personal injury.
Keep these agents out of the reach of children, preferably in a
locked cabinet.
• Do not tamper the washer-extractor controls and do not by-
pass the safety instructions and the warnings.
• Do not use some means on the soap dispenser lid to hold it
open by filling or when the machine operates. The discharge
or splashing of hazardous liquid can cause serious scalding
and burning.
• Do not operate the appliance when parts are broken or miss-
ing or when covers are open. The appliance must not be oper-
ated until the fixed guards are put correctly in place.
• The appliance must not be stored, installed or exposed to the
weather, extreme low or high temperature and humidity lev-
els. Do not hose down the washer. NEVER allow the appli-
ance to get wet.
• Check the functioning of the door lock mechanism on regular
base. NEVER bypass the doorlock mechanism.
• Disconnect the power and close all water and steam supply
before cleaning, servicing and at the end of each operating
day.
• Out of the venting on the upper part of the washer can escape
warm vapor or and hot air. Do not cover the vent but protect it
sufficiently. It serves air gap and as a vapor outlet to prevent
pressure building in the washer.
• Information contained in this manual is intended for use by a
qualified service technician familiar with proper and safe pro-
cedures to be followed when repairing an electrical appliance.
All tests and repairs should be performed by a qualified serv-
ice technician equipped with proper tools and measuring devi-
ces. All component replacements should be made by a quali-
fied service technician using only factory approved replace-
ment parts.
• Improper assembly or adjustment may occur if service or re-
pair is attempted by persons other then qualified service tech-
nicians or if parts other then approved replacement parts are
used. Improper assembly or adjustment can create hazardous
conditions.
• There can be a risk of injury or electrical shock while per-
forming services or repairs. Injury or electrical shock can be
serious or even fatal. Consequently, extreme caution should
be taken while performing voltage checks on individual com-
ponents or a product. PLEASE NOTE: Except as necessary to
perform a particular in servicing a product, the electrical pow-
er supply should ALWAYS be disconnected when servicing a
product.
• All industrial (OPL - On Premise Laundry) washers are de-
signed for use in Laundry with professionally trained attend-
ants.
• Before the appliance is removed from service or discarded,
remove the door.
• Any Water or Steam Leaks Must Be Repaired Immediately.
Closed supply immediately.
• If any problems or failures should arise, immediately contact
your dealer, serviceman or manufacturer.
• The manufacturer reserves the right to change the manuals
without previous notice.
WARNING
This appliance must be connected to a grounded
metal, permanent wiring system, and additionally an
equipment-grounding conductor must be run with
the circuit conductors and connected to the equip-
ment-grounding terminal or lead on the appliance.
C180
WARNING
In order to minimize the risk of fire, electrical shock
and injury, THIS WASHER MUST BE PROPERLY
GROUNDED. Never plug in or direct-wire an appli-
ance unless it is properly grounded in accordance
with all local and national codes.
If more appliances in the same location, mutual
grounding must be applied where possible.
C181
WARNING
Always consult the static requirements with a static
engineer in order to meet the requirements of per-
missible loads, vibrations and noise level in the
building! The washer extractor is intended to be per-
manently connected, it must be secured mounted to
a non-combustible, adequate floor structure. A con-
crete floor is required. Metal reinforced wood floors
are not allowed due to the risk of fire and excessive
vibrations. Never install the washer on an upper floor
or over a basement without a load support designed
by a structural engineer.
C184
IMPORTANT SAFETY INSTRUCTIONS
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
22
Part No. D1612ENR3
