Alliance Laundry Systems 802957R3 Скачать руководство пользователя

Страница: 29 / 48

Installation

802957

Step 9: (Washer Only) Remove the Shock
Sleeves and Shipping Brace

Remove front access panel by removing the two

screws at the bottom of the panel.
Remove the five bolts and lockwashers from shipping

brace with 9/16 inch wrench and remove brace. Refer

Figure 27

. Four bolts are located on the unit base

and one is holding the brace to the weight. Remove all

four shock sleeves by pulling on the yellow rope.

Refer to

Figure 27

IMPORTANT: The shipping brace, bolts,

lockwashers and shock sleeves should be saved and

MUST be reinstalled whenever the unit is moved

more than 4 feet (1.22 m). Do not lift or transport

unit from front or without shipping materials

installed. Refer to the

Maintenance

section for

proper instructions on reinstalling the shipping

materials.

Remove label from front side of front access panel and

place on backside of front access panel for future

reference.
Store the shipping materials in the accessories bag.

Save materials for use whenever the unit is moved.
Reinstall front access panel.

IMPORTANT: DO NOT tip washer more than

6 inches (152.4 mm) in any direction after shipping

brace has removed. Shock absorbers may separate

and damage to unit may result. For leveling

purposes, the unit may be tilted a maximum of

6 inches (152.4 mm) in any direction.

Step 10: Wipe Out Inside of Washer Drum
and Dryer Drum

Before using the washer and dryer for the first time,

use an all-purpose cleaner, or a detergent and water

solution, and a damp cloth to remove shipping dust

from inside the drums.

Figure 27

Figure 28

FLW2124N

Shock Sleeves

Motor Mount

Hooked End of Shipping Brace

Bolts and Lockwashers

Figure 26

FLW2124N

SWD939N

H315I

SWD939N

Содержание 802957R3

















































Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды

Alliance Laundry Systems 802957R3, Руководство по установке и эксплуатации

Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды