Alliance Laundry Systems 802957R3 Скачать руководство пользователя

Страница: 8 / 48

Safety Information

802957

28. Remove laundry immediately after the dryer

stops.

29. Always read and follow manufacturer’s

instructions on packages of laundry and cleaning

aids. Heed all warnings or precautions. To reduce

the risk of poisoning or chemical burns, keep

them out of reach of children at all times

(preferably in a locked cabinet).

30. Do not tumble fiberglass curtains and draperies

unless the label says it can be done. If they are

dried, wipe out the cylinder with a damp cloth to

remove particles of fiberglass.

31. Be sure water connections have a shut-off valve

and that fill hose connections are tight. CLOSE

the shut-off valves at the end of each wash day.

32. ALWAYS follow the fabric care instructions

supplied by the garment manufacturer.

33. Never operate the unit with any guards and/or

panels removed.

34. DO NOT operate the unit with missing or broken

parts.

35. DO NOT bypass any safety devices.

36. Failure to install, maintain, and/or operate this

machine according to the manufacturer’s

instructions may result in conditions which can

produce bodily injury and/or property damage.

37. Do not operate washer and dryer if the units have

been separated.

IMPORTANT: Solvent vapors from dry-cleaning

machines create acids when drawn through the

heater of the drying unit. These acids are corrosive

to the dryer as well as to the laundry load being

dried. Be sure make-up air is free of solvent vapors.

IMPORTANT: Have your unit installed properly.

Don’t do it yourself unless you know how!

NOTE: The WARNING and IMPORTANT

SAFETY INSTRUCTIONS appearing in this

manual are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining, or operating the dryer.

Always contact your dealer, distributor, service agent

or the manufacturer about any problems or conditions

you do not understand.

Содержание 802957R3

















































Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды

Alliance Laundry Systems 802957R3, Руководство по установке и эксплуатации

Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды