Alliance Laundry Systems 802957R3 страница 30 Скачать руководство пользователя

Страница: 30 / 48

Installation

802957

Step 11: Plug In the Washer and Dryer

Electric Dryer

Connect the dryer to an electrical power source. Refer

to Step 6 for information on connecting power cord.

Figure 29

Gas Dryer

Dryer requires 120 Volt, 60 Hertz electrical supply and

comes equipped with a 3-prong grounding plug. Refer

to serial plate for specific electrical requirements.

NOTE: The wiring diagram is located behind the

control panel, inside the control cabinet.

When plugging in the dryer:



Do not overload circuits.



Do not use an adapter.



Do not use an extension cord.



Do not operate both a washer and gas dryer on

the same circuit. Use separately fused 15 Amp

circuits.

The dryer is designed to be operated on a separate

branch, polarized, three-wire, effectively grounded,

120 Volt, 60 Hertz, AC (alternating current) circuit

protected by a 15 Ampere fuse, equivalent fusetron or

circuit breaker.
The three-prong grounding plug on the power cord

should be plugged directly into a polarized three-slot

effectively grounded receptacle rated 120 Volts AC

(alternating current) 15 Amps. Refer to

Figure 30

determine correct polarity of the wall receptacle.

Grounding Information

The dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current. The dryer is equipped

with a cord having an equipment-grounding conductor

and a three-prong grounding plug. The three-prong

grounding plug on the power cord should be plugged

directly into a polarized three-slot effectively

grounded receptacle rated 110/120 Volts AC

(alternating current) 15 Amps.

Do not modify the plug provided with the dryer – if it

will not fit the outlet, have a proper outlet installed by

a qualified electrician.

NOTE: Have a qualified electrician check the

polarity of the wall receptacle. If a voltage reading

is measured other than that illustrated, the

qualified electrician should correct the problem.

Do not operate other appliances on the same circuit

when this appliance is operating.

D275I

Connect to 30 Amp circuit.

To reduce the risk of fire, electric shock,

serious injury or death, all wiring and

grounding MUST conform with the latest

edition of the National Electrical Code,

ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1, and such local

regulations as might apply. It is the

customer’s responsibility to have the wiring

and fuses installed by a qualified electrician

to make sure adequate electrical power is

available to the dryer.

W521

WARNING

This dryer is equipped with a three-prong

(grounding) plug for your protection

against shock hazard and should be

plugged directly into a properly grounded

three-prong receptacle. Do not cut or

remove the grounding prong from this plug.

W036

WARNING

Improper connection of the equipment-

grounding conductor can result in a risk of

electric shock. Check with a qualified

electrician or service person if you are in

doubt as to whether the dryer is properly

grounded.

W038

WARNING

Содержание 802957R3

















































Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды

Alliance Laundry Systems 802957R3, Руководство по установке и эксплуатации

Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды