Alliance Laundry Systems 802957R3 Скачать руководство пользователя

Страница: 3 / 48

802957

IMPORTANT: Purchaser must consult the local gas supplier for suggested instructions to be followed if the

dryer user smells gas. The gas utility instructions plus the SAFETY and WARNING note directly above

must be posted in a prominent location near the dryer for customer use.

The following information applies to the state of Massachusetts, USA.



This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.



This appliance must be installed with a 36 inch (91 cm) long flexible gas connector.



A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance.



This appliance must not be installed in a bedroom or bathroom.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

– Do not try to light any appliance.

– Do not touch any electrical switch; do not use any phone in your building.

– Clear the room, building or area of all occupants.

– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

– If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

W052

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage, personal injury or death. Keep this

manual for future reference. If this machine changes ownership, this manual must

accompany machine.

W755

WARNING

• Installation of unit must be performed by a qualified installer.

• Install clothes dryer according to manufacturer’s instructions and local codes.

• DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (foil

type) duct is installed, it must be of a specific type identified by the appliance manufacturer

as suitable for use with clothes dryers. Refer to section on connecting exhaust system.

Flexible venting materials are known to collapse, be easily crushed, and trap lint. These

conditions will obstruct clothes dryer airflow and increase the risk of fire.

W729R1

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

W053

Содержание 802957R3

















































Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды

Alliance Laundry Systems 802957R3, Руководство по установке и эксплуатации

Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды