background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Safety Information

5

802957

7. Do not reach into the washer or dryer if the 

cylinders are revolving.

8. Do not install or store the unit where it will be 

exposed to water and/or weather.

9. Do not tamper with the controls.

10. Do not repair or replace any part of the unit, or 

attempt any servicing unless specifically 

recommended in the User-Maintenance 

instructions or in published user-repair 

instructions that you understand and have the 

skills to carry out.

11. Do not add gasoline, dry-cleaning solvents, or 

other flammable or explosive substances to the 

wash water. These substances give off vapors that 

could ignite or explode.

12. Do not use fabric softeners or products to 

eliminate static unless recommended by the 

manufacturer of the fabric softener or product.

13. To reduce the risk of an electric shock or fire, DO 

NOT use an adapter to connect the unit to the 

electrical power source.

14. To reduce the risk of fire, DO NOT DRY plastics 

or articles containing foam rubber or similarly 

textured rubberlike materials.

15. ALWAYS clean the lint filter after every load. A 

layer of lint in the filter reduces drying efficiency 

and prolongs drying time.

16. Keep area around the exhaust opening and 

adjacent surrounding area free from the 

accumulation of lint, dust and dirt.

17. The interior of the dryer and the exhaust duct 

should be cleaned periodically by qualified 

service personnel.

18. If not installed, operated and maintained in 

accordance with the manufacturer’s instructions 

or if there is damage to or mishandling of this 

product’s components, use of this product could 

expose you to substances in the fuel or from fuel 

combustion which can cause death or serious 

illness and which are known to the State of 

California to cause cancer, birth defects or other 

reproductive harm.

19. Washer and dryer will not operate with the 

loading door open. DO NOT bypass the door 

safety switches by permitting the washer or dryer 

to operate with the doors open. The washer and 

dryer will stop tumbling when the doors are 

opened. Do not use the washer or dryer if they do 

not stop tumbling when the doors are opened or 

start tumbling without pressing the START 

mechanisms. Remove the unit from use and call 

the service person.

20. Do not put articles soiled with vegetable or 

cooking oil in the washer or dryer. Due to the oil, 

the fabric may catch on fire by itself.

21. To reduce the risk of fire, DO NOT put clothes 

which have traces of any flammable substances 

such as machine oil, flammable chemicals, 

thinner, etc., or anything containing wax or 

chemicals such as in mops and cleaning cloths, or 

anything dry-cleaned at home with a dry-

cleaning solvent in the dryer.

22. Use your washer only for its intended purpose, 

washing clothes.

23. Use the dryer only for its intended purpose, 

drying clothes.

24. Always disconnect the electrical power to the 

washer and dryer before attempting service to 

either unit. Disconnect the power cords by 

grasping the plug, not the cord.

25. If the supply cord is damaged, it must be replaced 

by a special cord or assembly available from the 

manufacturer or its service agent.

26. Install this unit according to the 

INSTALLATION INSTRUCTIONS. All 

connections for electrical power, grounding and 

gas supply must comply with local codes and be 

made by licensed personnel when required. Do 

not do it yourself unless you know how!

27. Keep your unit in good condition. Bumping or 

dropping the unit can damage safety features. If 

this occurs, have your unit checked by a qualified 

service person.

Содержание 802957R3

















































Отзывы: