Alliance Laundry Systems 802957R3 страница 38 Скачать руководство пользователя

Страница: 38 / 48

Operation

802957

Operation Instructions for Dryers

IMPORTANT: Before using dryer for the first

time, use an all-purpose cleaner, or a detergent and

water solution, and a damp cloth to remove

shipping dust from inside of dryer drum.

IMPORTANT: Remove all sharp objects from

laundry to avoid tears and rips to items during

normal machine operation.

Step 1: Clean Lint Filter

Clean lint filter before each use.

Figure 43

Step 2: Load Laundry

Load clothes loosely into dryer drum. Add fabric

softener sheet if desired.

IMPORTANT: To avoid damage to dryer, do not

use more than one fabric softener sheet per load.

Figure 44

Step 3: Close Loading Door

Close loading door. Dryer will not operate with the

door open.

Figure 45

D608I

Lint Filter

To reduce the risk of fire, electric shock,

or injury to persons, read the IMPORTANT

SAFETY INSTRUCTIONS before operating

this appliance.

W727

WARNING

D609I

SWD943N

D609I

SWD943N

Содержание 802957R3

















































Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды

Alliance Laundry Systems 802957R3, Руководство по установке и эксплуатации

Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды