Alliance Laundry Systems 802957R3 Скачать руководство пользователя

Страница: 48 / 48

Installer Checklist

Fast Track for Installing the Stacked Washer and Dryer

(Refer to the manual for more detailed information)

• Position Unit Near Area

of Installation.

CHECK

• Connect Fill Hoses.

CHECK

TLW1976N

HOT

COLD

TLW1976N

• Connect Drain Hose to

Drain Receptacle

CHECK

SWD631N

Non-Gravity Drain Models Only

• Connect Drain Outlet to

Drain System.

CHECK

SWD745N

Gravity Drain Models Only

• Connect Gas Supply

Pipe.

• Check for Gas Leaks

Gas Dryer Only

CHECK

D434I

• Connect Electrical Plug.

Electric Dryer Only

CHECK

D679IE0A

• Connect Dryer

Exhaust System.

CHECK

H312I

• Position and Level the

Unit.

CHECK

SWD937N

• Remove the Shock Sleeves

and Shipping Brace.

Washer Only

H336I

CHECK

• Wipe Out Inside of

Washer Drum and

Dryer Drum.

SWD939N

H315I

GAS DRYERS

AND WASHERS

CHECK

D254I

• Plug In Washer

and Dryer.

ELECTRIC

DRYERS

D275IE0E

D254I

CHECK

• Recheck Steps 1-11

DRY2235N

CHECK

• Check Heat

Source

DRY2235N

Содержание 802957R3

















































Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды

Alliance Laundry Systems 802957R3, Руководство по установке и эксплуатации

Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды