Alliance Laundry Systems 802957R3 Скачать руководство пользователя

Страница: 15 / 48

Installation

802957

Step 5: (Gas Dryer Only) Connect Gas
Supply Pipe

1. Make certain your dryer is equipped for use with

the type of gas in your laundry room. Dryer is

equipped at the factory for

Natural Gas

with a

3/8 inch NPT gas connection.

NOTE: The gas service to a gas dryer must

conform with the local codes and ordinances, or in

the absence of local codes and ordinances, with the

latest edition of the National Fuel Gas Code ANSI

Z223.1/NFPA 54 or the CAN/CSA-B149.1 Natural

Gas and Propane Installation Code.

Natural Gas

, 1000 Btu/ft

(37.3 MJ/m

) service must

be supplied at minimum 5.0 inch water column

pressure to maximum 10.5 inch water column

pressure.
For proper operation at altitudes above 2000 feet

(610 m) the natural gas valve spud orifice size must be

reduced to ensure complete combustion. Refer to

Table 1

2. Remove the shipping cap from the gas

connection at the rear of the dryer. Make sure you

do not damage the pipe threads when removing

the cap.

3. Connect to gas supply pipe.

To reduce the risk of gas leaks, fire or

explosion:

• The dryer must be connected to the type

of gas as shown on nameplate located in

the door recess.

• Use a new flexible stainless steel

connector.

• Use pipe joint compound insoluble in L.P.

(Liquefied Petroleum) Gas, or Teflon tape,

on all pipe threads.

• Purge air and sediment from gas supply

line before connecting it to the dryer.

Before tightening the connection, purge

remaining air from gas line to dryer until

odor of gas is detected. This step is

required to prevent gas valve

contamination.

• Do not use an open flame to check for gas

leaks. Use a non-corrosive leak detection

fluid.

• Any disassembly requiring the use of

tools must be performed by a suitably

qualified service person.

W316

WARNING

Natural Gas Altitude Adjustments

Altitude

Orifice Size

Part

Number

feet

inches

2,000

610

0.0960

2.44

503776

3,000

915

0.0935

2.37

503777

5,500

1,680

0.0890

2.26

503778

7,000

2,135

0.0860

2.18

58719

9,000

2,745

0.0820

2.08

503779

10,500

3,200

0.0810

2.06

503780

Table 1

Содержание 802957R3

















































Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды

Alliance Laundry Systems 802957R3, Руководство по установке и эксплуатации

Результаты поиска

Содержание 802957R3

Отзывы:

Похожие инструкции для 802957R3

Бренды по названию

Популярные бренды