ALDI ABP1815MA Скачать руководство пользователя страница 97

Страница: 97 / 168

AFTER SALES SUPPORT

1300 889 028 (toll free)

MODEL No.:

CSC165XA.9 • 2323 • 05/2019

e-mail:

[email protected]

Troubleshooting

Fault

Cause

Remedy

The Battery pack gets

warm when charging.

It’s a result of the stepping

down of the chemical

reactions inside the

batteries during the

charging process.

This is normal.

Undiagnosable Fault. The tool needs to be

repaired.

Return the tool to a

service centre for repair

or contact Customer

Service.

The machine does

not start up when

operating the on/off

switch.

Low battery.

Charge the battery.

Defective motor.

Contact Customer

Service.

Cutting depth is less

than is set.

Sawdust accumulated at

the rear of the base.

Shake out sawdust.

Consider connecting

a vacuum for dust

collection.

Blade spins or slips

Blade is not tightly

engaged with the spindle.

Re-assemble the blade as

described in ASSEMBLY

section.

Blade does not cut a

straight line.

Blade is dull.

Mount a new, sharp

blade on the saw.

Blade is not mounted

properly.

Check that blade is

properly mounted.

Saw is not being guided

properly.

Use a parallel guide.

Blade kicks back

when beginning a

cut.

Blade is not spinning fast

enough.

Allow the saw blade to

reach full speed prior to

beginning a cut in the

material.

Содержание ABP1815MA









































































































































































Результаты поиска

Содержание ABP1815MA

Отзывы:

Похожие инструкции для ABP1815MA

Бренды по названию

Популярные бренды

ALDI ABP1815MA, Инструкция по эксплуатации

Результаты поиска

Содержание ABP1815MA

Отзывы:

Похожие инструкции для ABP1815MA

Бренды по названию

Популярные бренды