ALDI ABP1815MA Скачать руководство пользователя страница 120

Страница: 120 / 168

AFTER SALES SUPPORT

1300 889 028 (toll free)

e-mail:

[email protected]

CPS18WA.9 • 2323 • 05/2019

MODEL No.:

CPS18WA.9 • 2323 • 05/2019

14. Troubleshooting

Fault

Cause

Remedy

The Battery pack gets

warm when charging.

It’s a result of the stepping
down of the chemical reactions
inside the batteries during the
charging process.

This is normal.

Undiagnosable Fault. The tool needs to be repaired.

Contact Customer
Service

Low efficiency in

sanding

Too much dust in the dust bag.

Clean and empty
the dust bag.

The sander does not

start up after turning

on.

Battery depleted.

Charge the battery.

Defective on/off switch.

Contact Customer
Service.

Defective motor.

Contact Customer
Service.

The sander stops

during use.

Low battery.

Charge the battery.

Workpiece sanding is

not smooth. Sanding

marks are appearing .

Rough sanding paper. The
density of grit is too low.

Change to a proper
sanding paper with
a higher grit.

Low sanding efficiency.

Worn sanding paper.

Replace it with new
sanding paper.

The density of grit of the
sanding paper is too high.

Change to a
sanding paper with
lower grit.

Содержание ABP1815MA









































































































































































Результаты поиска

Содержание ABP1815MA

Отзывы:

Похожие инструкции для ABP1815MA

Бренды по названию

Популярные бренды

ALDI ABP1815MA, Инструкция по эксплуатации

Результаты поиска

Содержание ABP1815MA

Отзывы:

Похожие инструкции для ABP1815MA

Бренды по названию

Популярные бренды