Aisin AWGP180E1NHS Скачать руководство пользователя страница 24

Страница: 24 / 76

Header branching

* When total capacity of connected indoor unit exceeds 130% of rated capacity, restrict the permissible piping

length (actual length) to 328ft.

Layout example

(When 6 indoor units are

connected)

Note: If there is a height differ-

ence between the loca-

tions of indoor and

outdoor units, apply a

small “trap pipes” only on

the vapor line at least

every 32’ 10” (10 m) as illustrated.

Permissible

piping

length

Maximum piping length (L)

(Equivalent length/Actual length)

Maximum piping length after the first branch ( )

Piping length difference after the first branch

(when “a” is the shortest length after the first

branch)

- a

Permissible

height

difference

Height difference between indoor unit and out-

door unit (H)

When outdoor unit is higher than indoor unit
When outdoor unit is lower than indoor unit

Height difference between indoor units (h)

Branch

piping

How to select the header piping kit

• Connect crimp piping (locally required) to the branching points (on the indoor unit connection side) in

accordance with the number of connected indoor units.

• Refer to the header branching kit (sold separately) for the crimp piping size.

Total capacity of down-

stream indoor units (Btu/h)

Header kit type

Number of branches

less than 76.000

76.000 or more

and less than 112.000

KHRP26M33H

KHRP26M22H

KHRP26M73H

Up to 8 branches

Up to 4 branches

112.000 or more

and less than 234.000

KHRP26M72H

234.000 or more

Important reminder:

• Be sure to use the header branching and indoor unit piping that correspond to the indoor unit connecting

piping size.

• Always install the header branching joint (both vapor and liquid sides) so that the joint branches

horizontally. (Refer to “4-5. Notes for branch piping” on page 30).

•

Re-branching after the header branching is not allowed. Besides, the indoor unit with capacity of

96.000 Btu/h or larger can not be connected after the header branching.

32’ 10”

(10 m)

197 ft (60 m or less)

623/541 ft (190/165 m or less)

131 ft (40 m or less)

49 ft (15 m or less)

164 ft (50 m or less)

Содержание AWGP180E1NHS













































































Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды

Aisin AWGP180E1NHS, Руководство по установке

Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды