Aisin AWGP180E1NHS Скачать руководство пользователя страница 67

Страница: 67 / 76

Main Unit and Piping

Electrical

Test Operation

Reference

Test Operation

3) Connection condition check

Check if the wiring between outdoor and indoor units are connected correctly with the display indicated on the mas-

ter and the sub outdoor units.

The display is as follows.

�

In the case of Combination Multi master unit, or single outdoor unit

�

In the case of Combination Multi sub unit

Check both the master and the sub unit displays, and make sure that the number of connected indoor and outdoor

units and the sub unit address are properly displayed.

If the connection condition display agrees with the actual condition, press SET switch on the master unit for 2 sec-

onds or longer to fix the connection condition. (Current connection condition is memorized.)

After fixing the connection status, the display automatically proceeds to “4) Connection condition display.“

When the connection condition is not correct, turn OFF the power supply and check the wiring, and then turn the

power supply ON again.

The sub unit proceeds automatically to “4) Connection status display“ when the master unit memorizes the connec-

tion condition information.

ＣＯＤＥＮｏ．

ＵＰ

ＤＯＷＮ

ＳＷ２

ＳＷ３

ＳＷ４

ＳＷ５

ＳＷ６

ＩＮＤＯＯＲ

ＳＥＬＥＣＴ

ＭＯＤＥ

ＳＥＬＥＣＴＣＬＥＡＲＳＥＴ

ＣＯＤＥＮｏ．

ＵＰ

ＤＯＷＮ

ＳＷ２

ＳＷ３

ＳＷ４

ＳＷ５

ＳＷ６

ＩＮＤＯＯＲ

ＳＥＬＥＣＴ

ＭＯＤＥ

ＳＥＬＥＣＴＣＬＥＡＲＳＥＴ

ＣＯＤＥＮｏ．

ＵＰ

ＤＯＷＮ

ＳＷ２ＳＷ３

ＳＷ４

ＳＷ５

ＳＷ６

ＩＮＤＯＯＲ

ＳＥＬＥＣＴ

ＭＯＤＥ

ＳＥＬＥＣＴＣＬＥＡＲＳＥＴ

Содержание AWGP180E1NHS













































































Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды

Aisin AWGP180E1NHS, Руководство по установке

Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды