Aisin AWGP180E1NHS Скачать руководство пользователя страница 11

Страница: 11 / 76

Main Unit and Piping

Electrical

Test Operation

Reference

3. Installation

3-3. Foundation and anchor bolt specifications

1) Foundation shape

�

The foundation must have sufficient strength in accordance with the drawings below. In order to protect the out-

door unit from rain, dust or damage, the height of the foundation must be 8 inch (200) from the ground.

The foundation must have grooves around itself that directs drain water to the drainage port.

�

The foundation must support the mass of the outdoor unit evenly and must be flat and smooth so that water will

not accumulate on the upper surface.

�

Never use a foundation that consists of more than one piece of block. Such a foundation will not provide neces-

sary strength.

�

Condensation water may drip from the bottom of the outdoor unit. Install a drain pan if the condensation water

could cause problems.

Warning

�

The foundation must provide a firm and level surface for installing the outdoor unit so that the

outdoor unit does not tip over in the event of strong winds (gust, etc.) or earthquakes.

If the foundation strength is insufficient, the outdoor unit could tip over and cause fuel gas
leakage or injury.

Installation location/

Designed earthquake resistance

Foundation dimensions feet (mm)

Anchor bolt spacing feet (mm)

Ground/

Horizontal 0.4 G, Vertical 0.2 G

5-3/4’ (1750)

3’ 1/8” (956)

Important reminder

�

If the foundation is smaller than the specified dimensions or if the designed earthquake resis-

tance value needs to be higher than that shown in the table above, appropriate design change

such as connecting the foundation to the building (floor slab) with steel rods is necessary. Such

design changes should be done in accordance with the appropriate building equipment seismic

tolerance design and installation policy.

Anchor bolts

8 (200)

1-13/32 (35)

Drainage grooves

Chamfered corners
on the concrete

(Foundation concrete)

Anchor bolts

Length: inch (mm)

a or more

b or more

oundation concrete)

(Anchor bolt

spacing)

(Anchor bolt

spacing)

2’ 8” (841)

4’ (1100)

Содержание AWGP180E1NHS













































































Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды

Aisin AWGP180E1NHS, Руководство по установке

Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды