Aisin AWGP180E1NHS Скачать руководство пользователя страница 53

Страница: 53 / 76

Main Unit and Piping

Electrical

Test Operation

Reference

Various Function Settings

12. Various Function Settings

All function settings of the outdoor unit in this model are performed by board maintenance function.

12-1. Address setting method of the indoor and outdoor units

�

The address setting of the outdoor and indoor units is performed automatically.

�

When the centralized remote controller is added, set the centralized address to the indoor units with the

standard remote controller.

12-2. EEP dip switch setting

This model has EEP dip switches inside the outdoor unit circuit board.

Refer to “List of EEP dip switch settings” on the following page for the contents of the switches and the factory

default setting
.

Warning

�

Be sure to change the #4 pin of #1 EEP dip switch to “ON” when the deodorizing option is

installed.

If not, the protection device may operate improperly and smoke, fire or malfunction could

occur.

Caution

�

Do not touch the moving parts (fans or a belt around the engine).

You could be caught by the moving parts and be injured.

The fans or the engine may automatically start running to protect the device to maintain perfor-

mance even if the GHP is stopped.

Be sure to turn OFF the power breaker when you need to touch the moving parts.

Содержание AWGP180E1NHS













































































Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды

Aisin AWGP180E1NHS, Руководство по установке

Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды