Aisin AWGP180E1NHS Скачать руководство пользователя страница 31

Страница: 31 / 76

Main Unit and Piping

Electrical

Test Operation

Reference

4. Refrigerant Piping

4-6. Stop valve connections and opening/closing

1) Stop valve connections

�

Both of liquid and vapor line piping’s must be brazed when connecting.

2) Opening and closing the stop valves

�

Open the liquid line stop valve and then open the vapor line stop valve.

1. Remove the cap.

2. Turn the valve shaft by 90° counterclockwise with an

open-end wrench. The valve is fully opened at the

position where the pin hits the stopper.

3. Firmly tighten the cap.

Important reminder

�

Connect refrigerant piping with the stop valves on the outdoor unit fully closed (factory default).

Do not operate the stop valves until all the refrigerant piping for the indoor and outdoor units have

been connected, and the refrigerant leakage test, vacuuming operation and additional refrigerant

charging has been completed. Note that both the vapor and the liquid line valves must be fully

open in operating.

�

Make sure not to damage the power supply wire, the communication wire, the condensation water

drain port or the exhaust water drain hose by brazing flame when brazing the refrigerant pipes to

the stop valves.

< Liquid / Vapor >

< Vapor line >

Fully closed (Factory default)

Fully open

Valve shaft

Liquid line

26 to 32 N•m

Vapor line

26 to 32 N•m

19.2 to 23.6 Ibsft

Содержание AWGP180E1NHS













































































Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды

Aisin AWGP180E1NHS, Руководство по установке

Результаты поиска

Содержание AWGP180E1NHS

Отзывы:

Похожие инструкции для AWGP180E1NHS

Бренды по названию

Популярные бренды