Airxcel Aqua-Hot 200 Series Скачать руководство пользователя страница 63

Страница: 63 / 105

Fluid Circulation Pump

©Aqua-Hot®

250-D03 Diesel Series Service Manual

REV 220302

p. 63

Burner Components

Be sure to reattach the diesel burner head prior to

turning the heater ON� Failure to do so may result in

ignition of the diesel burner and serious bodily injury.

Fuel Nozzle Cleaning and Maintenance:

The fuel nozzle is a precision calibrated part and

cannot

be cleaned or serviced. A replacement of the fuel nozzle is

recommended annually.

Fuel Nozzle Replacement Procedure:

1. Use a ¾” wrench to hold the fuel nozzle stand hex while

loosing the fuel nozzle with a ⅝” wrench and remove as

shown in Figure 102.

2. When replacing the fuel nozzle, be sure to tighten the

nozzle, loosen it a ¼ turn, and then firmly re-tighten. This

will establish a seated fit and avoid any leaks.

3. After replacing the fuel nozzle, reattach the diesel burner

head.

4. Turn ON the diesel burner for 5 seconds, then turn it OFF.

This will activate the diesel burner’s prime-cycle and flush

the fuel system of any potential contaminants. Perform this

procedure twice.

5. Test for normal operation.

NOTE:

Be sure to use care when handling the new fuel

nozzle. Oils and/or small dust or dirt particles from your

hands may plug the nozzle’s small orifice. A partially plugged

orifice will restrict fuel flow, which will affect the combustion

process of the diesel burner.

Ignition Electrodes

Fuel Nozzle

Manifold Hex

Figure 104

Figure 102

⅝” Wrench

¾” Wrench

Figure 103

Fuel Nozzle

Содержание Aqua-Hot 200 Series










































































































Результаты поиска

Содержание Aqua-Hot 200 Series

Отзывы:

Похожие инструкции для Aqua-Hot 200 Series

Бренды по названию

Популярные бренды

Airxcel Aqua-Hot 200 Series, Руководство по обслуживанию

Результаты поиска

Содержание Aqua-Hot 200 Series

Отзывы:

Похожие инструкции для Aqua-Hot 200 Series

Бренды по названию

Популярные бренды