Airxcel Aqua-Hot 200 Series Скачать руководство пользователя страница 58

Страница: 58 / 105

Fluid Circulation Pump

©Aqua-Hot®

250-D03 Diesel Series Service Manual

REV 220302

p. 58

Burner Components

Flame Sensor Replacement:

1. In order to perform the following procedures, it is necessary

to detach the diesel burner head. Be sure to review the

detaching/reattaching instructions starting on Page 47.

Remove the screw that fastens the flame sensor to the

photo disc (as shown in Figure 96), and detach the flame

sensor’s green and blue wires from the C-plug harness’

green and violet wires. Remove the defective flame sensor.

Slide the tab of the new flame sensor into the provided slot

in the photo disc and secure in place with the screw.

Connect the flame sensor’s green wire to the green C-plug

harness wire (pin 6), and connect the blue wire to the

C-plug harness’ violet wire (pin 4).

5. Follow the instructions for reattaching the diesel burner

head on Page 50.

Flame Sensor

Green Wire

(to Diesel Burner)

Photo Disc

Blue Wire

Violet Wire

(to Diesel Burner)

NOTE:

This screw is used to fasten the

Flame Sensor to the Photo Disc. Remove

when replacing the Flame Sensor.

Figure 95

Figure 96

Содержание Aqua-Hot 200 Series










































































































Результаты поиска

Содержание Aqua-Hot 200 Series

Отзывы:

Похожие инструкции для Aqua-Hot 200 Series

Бренды по названию

Популярные бренды

Airxcel Aqua-Hot 200 Series, Руководство по обслуживанию

Результаты поиска

Содержание Aqua-Hot 200 Series

Отзывы:

Похожие инструкции для Aqua-Hot 200 Series

Бренды по названию

Популярные бренды