Airxcel Aqua-Hot 200 Series Скачать руководство пользователя страница 8

Страница: 8 / 105

Operating the LCD

©Aqua-Hot®

250-D03 Diesel Series Service Manual

REV 220302

p. 8

Operational Flow Chart

A heat source is selected from

Interior Control Panel

Electric Element

Electric Heating Element

will activate, providing

heat to the antifreeze and

water heating solution

within the boiler tank

The burner will begin

providing heat to the

antifreeze and water heating

solution present within the

boiler tank.

The antifreeze and water

heating solution in the boiler

tank heats to 180°F

An Interior Zone

Thermostat Calls

for Heat

A hot water faucet opens,

signaling a need for heat to the

boiler tank

The fluid circulation pump

activates and begins circulating

the heated antifreeze and water

solution throughout the interior

heating zone

The heating zone

fans activate

Heat is transferred to the

vehicle interior via the heat

exchangers

The cooled antifreeze

is returned to the boiler

tank to be reheated.

Hot water flows from the water

faucet

Heat is transferred to the

domestic hot water system

Diesel Burner

NOTE:

The Burner

and/or Electric

Element (as turned

ON) will automatically

begin reheating the

antifreeze and water

heating solution when

the boiler tank drops

below 155°F.

Содержание Aqua-Hot 200 Series










































































































Результаты поиска

Содержание Aqua-Hot 200 Series

Отзывы:

Airxcel Aqua-Hot 200 Series, Руководство по обслуживанию, Страница: 8 / 105

Результаты поиска

Содержание Aqua-Hot 200 Series

Отзывы: