Airxcel Aqua-Hot 200 Series Скачать руководство пользователя страница 64

Страница: 64 / 105

Fluid Circulation Pump

©Aqua-Hot®

250-D03 Diesel Series Service Manual

REV 220302

p. 64

Fuel Solenoid

The fuel solenoid allows the flow of diesel fuel to the diesel

burner’s fuel nozzle.

Fuel Solenoid Component Test:

1. Locate and detach the C-plug harness’ violet (+) and brown

(-) wires from the fuel solenoid.

2. Connect the (-) lead of a 12V DC power supply to the fuel

solenoid’s (-) electrical terminal.

3. Intermittently apply the (+) lead of the power supply to the

fuel solenoid’s (+) electrical terminal.

4. Listen for the fuel solenoid to click (open and close).
5. If the fuel solenoid does not click, it must be replaced.

NOTE:

If a long after-smoking condition exists during the

diesel burner’s purge cycle, the fuel solenoid valve kit may

need to be replaced.

NOTE:

If the fuel solenoid is not working, troubleshoot the

diesel burner’s high-limit thermostats (2). If they are tripped,

they will not allow the fuel solenoid to operate.

Fuel Solenoid Replacement Procedure:

1. Disconnect the C-plug harness’ violet (+) and brown (-)

wires from the fuel solenoid.

Using a 8mm wrench, remove the lock nut and flat washer

from the end of the fuel solenoid shaft and then pull the

fuel solenoid away from the nozzle stand approximately ½”.

Remove the fuel solenoid shaft from the nozzle manifold

using a 16mm wrench. Discard the shaft and valve kit,

as replacements are provided with the new fuel solenoid

assembly.

3. Insert the contents of the new fuel solenoid valve kit into

the new fuel solenoid shaft. Slide the new fuel solenoid

onto the fuel solenoid shaft. Thread the new fuel solenoid

shaft with the fuel solenoid to the fuel nozzle manifold and

tighten. Secure the fuel solenoid in place with the new flat

washer and lock nut.

4. Connect the C-plug harness’ (+) and brown (-) wires to the

fuel solenoid’s (+) and (-) electrical terminals.

5. Test for normal operation.

Retaining Clamp

Ignition Cable

Positive Terminal

Negative Terminal

Lock Nut

Retaining Clip

Photo Disc

Figure 105

Burner Components

Figure 106

Fuel Solenoid Valve Coil

Electrical Terminals

(+)

(-)

Fuel Solenoid

Valve Kit

Fuel Solenoid Valve Assembly

Fuel Solenoid

Shaft

Fuel Solenoid

Valve Coil

Содержание Aqua-Hot 200 Series










































































































Результаты поиска

Содержание Aqua-Hot 200 Series

Отзывы:

Похожие инструкции для Aqua-Hot 200 Series

Бренды по названию

Популярные бренды

Airxcel Aqua-Hot 200 Series, Руководство по обслуживанию

Результаты поиска

Содержание Aqua-Hot 200 Series

Отзывы:

Похожие инструкции для Aqua-Hot 200 Series

Бренды по названию

Популярные бренды