manualshive.com logo in svg

Air Monitor VELTRON DPT 2500-plus, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Air Monitor VELTRON DPT 2500-plus Скачать руководство пользователя страница 9

VELTRON DPT 2500-

plus

Air Monitor Corporation

116-047-20.PMD (5/5/11)

VELTRON DPT 2500-

plus

 - IO&M Manual

4

4 – INSTALLATION

SECTION 4 – INSTALLATION

4.1 – RECEIVING AND INSPECTION

• Carefully remove the VELTRON DPT 2500-

plus

 from the shipping container and inspect for any damage.  If any

damage has occurred in transit, cont

ac

t freight carrier.

• Save the shipping container for possible future use in returning the VEL

T

RON DPT 2500-

plus

 to the factory for

recalibration.

• Review the Factory Set-Up Information Sheet provided with the unit and verify the W

O

 # and Serial # match those

on the VE

LT

RON DPT 2500-

plus

. Verify that the configuration recorded on the Factory Set-Up Information Sheet is

correct for your application.  If not, cont

a

ct Air Monitor's Customer Service Dep

a

rtment at 1-800-AIRFLOW for

further guidance.

Note:

The VELTRON DPT 2500

-

plus

 has been configured and calibrated to customer specified parameters (see

"Factory Setup Information Sheet" provided with the unit), and requires no additional calibration/verification

prior to installation.

4.2 – LOCATION

• The standard version of the VEL

T

RON DPT 2500-

plus

 is a NEMA

 

1 enclosure suitable for most clean indoor

locations. If additional protection is required, mount unit in an enclosure with adequate NEMA rating.

• The industrial version of the VELTRON DPT 2500-

plus

 is housed in a NEMA 12 enclosure (see NEMA ratings for

degree of protection).

• The ambient temperature of the selected mounting location must be b40º to 120ºF

. Co

nsideration should

be given to uni

ts

 exposed to direct sunlight.

• The selected mounting location should be rigid and free of vibration.

Содержание VELTRON DPT 2500-plus





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды