Air Monitor VELTRON DPT 2500-plus Скачать руководство пользователя страница 15

Страница: 15 / 36

VELTRON DPT 2500-

plus

Air Monitor Corporation

116-047-20.PMD (5/5/11)

VELTRON DPT 2500-

plus

- IO&M Manual

SECTION 5 – OPERATION

5.5 – PUSHBUTTON DEFINITION

The four pushbuttons used to interface with the VEL

RON DPT 2500-

plus

are identified by their symbols.

symbols are defined as follows:

DOWN

ENTER

ESCAPE

In addition to Configuration programming, pushbuttons can be used for cert

n functions when in the

Normal

operation

mode. The following list describes the pushbutton function when in the

mal

operation mode and in the User Setup

(programming).

When in Normal Operation Mode.

Manually activates AUTO-zero (if AUTO-zero is ON).

Displays VELTRON DPT 2500-

plus

and software

version number. While software version is

displayed, press and work order number and serial number will be displayed. Press

and ID (if any) will be displayed. Press and the display will go back to the

Normal

operation

mode.

Activates the User Setup menu.

When in User Setup.

Use to scroll to the desired Main Menu item.

Use to scroll to the value or mode within a p

rameter.

Enters user into specific selection sub-menu from Main Menu Selection.

Displays current setting of selected Parameter. Enters the selected value or setting into memory.

Use as an escape key to exit Main Menu selection to avoid scrolling to "Return to MAIN MENU".

The following pushbutton combinations can be used to more quickly set user selected values (i.e. Process Min and

Max Values, Transducer Operating S

an, etc.).

Increase the second column digit.

Decrease the second column digit.

Increase the third column digit.

XXXXX

Decrease the third column digit.

Increase the fourth column digit.

Decrease the fourth column digit.

*Must be pressed and held before other button(s) are pressed.

Note: Pushbuttons are moment

ry type and should be quickly pressed and released to initiate desired change,

unless otherwise instructed to press and hold.

2nd Column

3rd Column

4th Column

then

and

Содержание VELTRON DPT 2500-plus





































Результаты поиска

Содержание VELTRON DPT 2500-plus

Отзывы:

Бренды по названию

Популярные бренды

Air Monitor VELTRON DPT 2500-plus, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание VELTRON DPT 2500-plus

Отзывы:

Бренды по названию

Популярные бренды